GE Refrigerator Main Control Board WR01F00241 – Genuine OEM

The main control board is the central processing unit of the refrigerator — it manages the compressor, evaporator and condenser fans, defrost heater, temperature sensors, ice maker, and dispenser functions. When it fails, the refrigerator loses the ability to regulate any of these systems. The result is a refrigerator that won’t cool, won’t defrost (leading to ice buildup on the evaporator coils), has fans that run constantly or not at all, or displays error codes that don’t clear after a power reset. Because the board controls everything, a single board failure can produce a wide range of seemingly unrelated symptoms. Part WR01F00241 is the genuine OEM GE main control board for compatible GE Profile and GE Café side-by-side and French door refrigerators, replacing WR55X11077, WR55X11097, and WR55X11098.

⚠️ Symptoms This Part Fixes

• Refrigerator not cooling — fresh food or freezer compartment at wrong temperature
• Refrigerator not defrosting — ice buildup on evaporator coils, frost visible on back wall of freezer
• Compressor not running — no cooling, no compressor hum
• Evaporator or condenser fan not running (or running constantly)
• Error codes on the display that don’t clear after unplugging and replugging
• Temperature display showing incorrect readings or flashing
• Ice maker not producing ice (board not sending signal to ice maker)
• Water dispenser not working
• Refrigerator runs constantly and never cycles off
• Refrigerator completely dead — no lights, no display, no response
• Intermittent cooling — works sometimes, fails other times
• Multiple unrelated functions failing simultaneously

✓ Part Details

• OEM Part Number: WR01F00241
• Replaces / Cross-References: WR55X11077, WR55X11097, WR55X11098
• Component: Main control board — manages compressor, fans, defrost, ice maker, dispenser, and temperature regulation
• Compatible Brands: GE, GE Profile, GE Café
• Condition: Genuine OEM — exact factory replacement board
• Note: This is a high-value electronic component. Verify compatibility with your full model number before ordering. Control boards are typically non-returnable once installed.

⚙️ Installation Notes

• Skill Level: Intermediate to Advanced — 30 to 60 minutes
• Disconnect power before starting — unplug the refrigerator completely
• The main control board is typically located in the rear lower section of the refrigerator behind an access panel, or in the top hinge area depending on model — consult your service manual for exact location
• Photograph all wiring harness connections before disconnecting — incorrect reconnection will cause the new board to malfunction
• Discharge any static electricity before handling the board — touch a grounded metal surface first
• Remove the old board by disconnecting all harnesses and removing the mounting screws
• Install the new WR01F00241 in the same orientation, reconnect all harnesses per your photos, and reinstall the access panel
• Restore power and allow the refrigerator 24 hours to reach stable operating temperatures before evaluating performance
• If error codes persist after board replacement, the fault may be in a sensor or component the board is monitoring — check thermistors and wiring harnesses

✓ Compatible Models

Fits GE Profile and GE Café side-by-side and French door refrigerators including: CFCP1RKBASS, CFCP1RKBDSS, CFSP5RKBBSS, CFSP5RKBCSS, CFSP5RKBDSS, CFSP5RKBESS, PDSE5NBZCDSS, PDSE5NBZHDSS, PFCF1RKZABB, PFCF1RKZAWW, PFCS1RKZASS, PFCS1RKZHSS, PFSF5RKZABB, PFSF5RKZAWW, PFSF5RKZCBB, PFSF5RKZCWW, PFSS5RKZASS, PFSS5RKZCSS, PFSS5RKZHSS, PGCS1RKZASS, PGCS1RKZHSS, PGCS1RKZJSS, PGS25KSEAFSS, PGSS5RKZASS, PGSS5RKZCSS, PGSS5RKZHSS, PGSS5RKZJSS, PVS21KSEAFSS, PVS21KSEBFSS.

Don’t see your model? Contact us with your full model number and we’ll verify fit before you order. Confirming compatibility is especially important for control boards.