Refrigerator Not Cooling or Starting? Main Control Board WR01F05358 – Fix Power & Cooling Failure Fast
If your GE refrigerator won't cool, won't start, or has completely lost power, the main control board is the most common root cause. In most GE French door and side-by-side refrigerators, this is caused by a failed main control board. When it fails, the board can no longer send operating signals to the compressor, fans, or defrost system — the fridge goes dark, warm, or enters a continuous error loop. ⚡ Common failure point in GE-built refrigerators, especially after power surges. Part WR01F05358 is the genuine OEM replacement that restores full refrigerator operation by re-establishing proper control of all cooling and electrical systems.
❓ Is This the Right Part?
This is the correct fix if ALL of the following are true:
- ✔ Refrigerator has power at the outlet — wall socket confirmed working
- ✔ Fridge is completely dead, not cooling, or stuck in error/alarm state
- ✔ Compressor, fans, or defrost system are unresponsive despite power being present
- ✔ ONLY problem is loss of cooling/control — water dispenser or ice maker may also be affected
Not sure? Send us your model number — we'll confirm before you order.
🔧 Common Symptoms
- Refrigerator completely dead — no lights, no fans, no compressor
- Fridge not cooling despite compressor attempting to run
- Continuous error codes or alarm beeping on display panel
- Defrost system not running — heavy frost buildup in freezer
- Ice maker or water dispenser stopped working alongside cooling loss
- Fridge restarting or cycling on/off repeatedly
✔ If these symptoms match, the main control board is the most likely failed component in the system.
✔ In most cases, replacing this control board restores full refrigerator operation immediately.
📦 Part Details
- Part Number: WR01F05358
- Type: Main Electronic Control Board — manages compressor, fans, defrost, and all refrigerator systems
- Replaces: WR01F05225, 239D6019G105
- Brands: GE (General Electric)
If the control board failed after a power surge, also inspect the Thermistor / Temperature Sensor — a surge that kills the board often damages sensors on the same circuit. Replacing a faulty thermistor at the same time prevents a second service call and ensures the new board reads temperatures accurately from day one.
⚙️ Installation
Skill Level: MODERATE — 30–45 minutes. Disconnect power before servicing. Pull the refrigerator away from the wall and remove the rear access panel or lower back cover to expose the control board housing. Photograph all wire harness connections before disconnecting. Unplug each connector from the old board, transfer them to the new WR01F05358 in the same positions, and secure the board in its mounting bracket. Reinstall the panel, restore power, and allow the refrigerator 24 hours to reach full operating temperature.
✓ Compatible Models
Confirmed compatible with GFE26JMMXFES, GFE26JYMXFFS, GNE27JGMYFBB, GNE27JGMYFWW, GNE27JMMXFES, GNE27JYMXFFS, GWE22JYMBFFS, GYE21JYMBFFS plus additional GE refrigerator models on the same platform. Contact us to verify your model number before ordering.
💡 Pro Tip
Main control boards have 6–10 wire harness connectors and getting one wrong will prevent the fridge from operating correctly after the repair. Take a clear photo of the entire board with all connectors in place before removing anything. This takes 30 seconds and eliminates the most common installation mistake. If your board shows visible burn marks or a blown component, also check the power inlet wiring harness — a shorted harness can destroy a new board within days.
✓ Model-Specific Repair Pages
✅Compatibility & Cross Reference
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
Buy Online Pick Up In-Store
Kitchener, Ontario N2E 1W8
- Choosing a selection results in a full page refresh.
