Refrigerator Frosting Up or Not Staying Cold? Door Gasket WR01L02128 – Fix Seal Failures & Frost Buildup Fast
When your GE refrigerator develops excessive frost, runs constantly, or can’t hold temperature, a failed grey door gasket is one of the most common and most overlooked causes. In most GE and GE Profile French door and side-by-side refrigerators, this is caused by a worn, torn, or hardened door gasket. When it fails, warm air infiltrates the refrigerator cavity continuously — causing frost accumulation on walls and coils, compressor overrun, rising energy bills, and eventual food spoilage. ⚡ Common wear failure in GE-built French door and side-by-side refrigerators. Part WR01L02128 is the genuine OEM replacement that restores a full airtight door seal and eliminates warm-air infiltration immediately — directly supersedes WR14X10316, 225D1567G003, WR01L02127, and 225D1567G002.
❓ Is This the Right Part?
This is the correct fix if ALL of the following are true:
- ✔ Refrigerator compressor and evaporator fan are confirmed working
- ✔ Refrigerator door closes fully and latch engages properly
- ✔ Defrost system is confirmed functional (no blocked drain)
- ✔ ONLY problem is frost buildup on walls/coils, warm fridge, or compressor running constantly
Not sure? Send us your model number — we'll confirm before you order.
🔧 Common Symptoms
- Excessive frost or ice buildup on refrigerator walls, shelves, or evaporator coils
- Refrigerator not maintaining set temperature despite compressor running
- Compressor runs continuously or cycles on/off more frequently than normal
- Visible gaps, tears, cracks, or stiff/brittle sections in the grey door seal
✔ If these symptoms match, this is the most likely failed component in the system.
✔ In most cases, replacing this door gasket restores a full airtight seal and normal refrigerator operation immediately.
📦 Part Details
- Part Number: WR01L02128
- Type: Refrigerator Door Gasket / Door Seal (Grey)
- Replaces: WR14X10316, 225D1567G003, WR01L02127, 225D1567G002 — no modification required
- Brands: GE, GE Profile, Monogram
While the door is open, inspect the door hinges and hinge pins for wear or misalignment — a sagging door puts uneven stress on the new gasket and will cause premature failure at the corners. Hinge kits are inexpensive and take minutes to swap at the same time.
⚙️ Installation
Skill Level: EASY — 15–25 minutes. No tools required for most models. Starting at a corner, pull the old gasket out of the door liner groove, work around the perimeter, then press the new gasket into the groove starting at the corners and working toward the middle of each side. Close the door and check for even contact around the full perimeter before restoring power.
✓ Compatible Models
Confirmed compatible with CFRS2MIDASS, GFML2KEXBGS, GFMS2KEBASS, GFRF2KBXABB, GFRS2KBXASS, GFSS2HCYASS, GFSS2KEYASS, GNR22DGEBFBB, MFBL2KEDAGP, PFM22KSGAFSS, PFRF2MBXABB, PFRS2MBXASS, PFRS2MIXASS, PFSF2MIXABB, PFSS2MIYASS, PNR22LGEBFBB series and additional GE and GE Profile models. Contact us to verify your model number before ordering.
💡 Pro Tip
Close the refrigerator door on a dollar bill. If you can pull it out with little resistance, the gasket is failing at that point. Test all four sides and both corners. If it slips at multiple spots, the gasket is the problem — and this grey WR01L02128 is the correct OEM replacement. A tight seal should grip the bill firmly and require a tug to remove.
✅Compatibility & Cross Reference
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
Buy Online Pick Up In-Store
Kitchener, Ontario N2E 1W8
- Choosing a selection results in a full page refresh.
