Burner Not Heating or Stuck on High? Surface Element Switch WS01F01663 – Fix Infinite Switch Failure Fast

If your GE electric range burner won't heat, won't turn off, or is locked on high, the surface element switch (infinite switch) is the most common cause. In most GE and Hotpoint electric ranges, this is caused by a failed infinite switch. When it fails, the switch loses the ability to cycle power to the burner element — leaving it either completely dead or dangerously stuck at full power. ⚡ Common failure point in GE-built electric ranges and cooktops. Part WS01F01663 is the genuine OEM replacement that restores precise burner temperature control across all heat settings.

❓ Is This the Right Part?

This is the correct fix if ALL of the following are true:

• ✔ Range powers on — clock, oven, and other burners function normally
• ✔ Burner element has been tested and confirmed functional (not burned out)
• ✔ Wiring to the switch terminal block is intact — no melted connectors or broken wires
• ✔ ONLY problem is one burner that won't heat, won't turn off, or has no temperature control

Not sure? Send us your model number — we'll confirm before you order.

🔧 Common Symptoms

• Burner won't heat or turn on at any setting
• Burner won't turn off — stays on after knob is turned to OFF
• Burner stuck on high heat (safety hazard — disconnect power immediately)
• No temperature control — only full on or full off
• Burner cycles on and off erratically or inconsistently
• Burner overheats or burns food at low settings
• Control knob turns freely but has no effect on burner output
• Burning smell or visible scorching at the switch terminals

✔ If these symptoms match, this is the most likely failed component in the system.

✔ In most cases, replacing this surface element switch restores normal operation immediately.

📦 Part Details

• Part Number: WS01F01663
• Type: Surface Element Switch (Infinite Switch) — 240V cycling switch that controls power delivery to electric burner elements across all heat settings
• Replaces: WB23M110, 222D3379P001, AP6885803, PS12728361
• Brands: GE, Hotpoint

⚙️ Installation

Skill Level: Moderate — 30 to 45 minutes. Disconnect power at the circuit breaker before starting — this is a 240V component. Remove the control knob, then unscrew the control panel to access the switch from behind. Photograph all wire connections before disconnecting — wire position on the terminal block is critical and incorrect reinstallation can recreate the failure. Transfer wires to the new switch in the same positions, secure with mounting screws, reassemble the panel, restore power, and test all heat settings.

✓ Compatible Models

Confirmed compatible with JCBP83DP2WW, PCB900DR1BB, PCB900DR1WW, PCB900DR3WW, PCB900DR4WW, PCB900SR4SS, PCB905SV1SS, PCB905SV3SS, PCB909DR1WW, PCB909DR3WW, PCB909DR4WW, PCB909SR1SS, PCB909SR3SS, PCB909SR4SS, PCB910SF1SS, PCB940DF1WW, PCB940SF1SS, PCB940SK1SS, PCB969DR1BB, PCB969DR1WW, PCB969DR2BB, PCB969DR3BB, PCB969DR3WW, PCB969SR2SS, PCB969SR3SS, PCB970SR1SS, PCB980DF1BB, PCB980DF1WW, PCB980SF1SS, PCB985DK1WW, PCB985EK1ES, PCB985SK1SS, PDS20SBRBRSS, PDS22SBRBRSS, PHP9036SJ1SS, PP9030DJ1BB plus additional GE and Hotpoint models. Contact us to verify your model number before ordering.

⚠️ Model hub links — BIDIR flagged for manual addition.

💡 Pro Tip

✓ Model-Specific Repair Pages