Oven Door Sagging, Loose, or Won’t Close Properly? WS01L14674 Right Side Door Hinge – Fix It Fast

A sagging oven door, a door that won’t stay closed, or uneven gaps around the door seal are the clearest signs of a failed oven door hinge. In most GE, GE Profile, and GE Café freestanding and slide-in ranges, the door hinge wears out or breaks at the pivot point after years of repeated opening and closing under heat stress. When it fails, the door hangs at an angle, the gasket seal is compromised, and heat escapes — affecting cooking performance and energy efficiency. ⚡ Common wear item on JGS, JCGS, PCS, PCGS, and PC2S series ranges. Part WS01L14674 is the genuine OEM right side door hinge that restores proper door alignment and a tight seal immediately.

❓ Is This the Right Part?

This is the correct fix if ALL of the following are true:

• ✔ Range powers on and burners / oven element operate normally
• ✔ Door gasket / seal is intact and undamaged
• ✔ Problem is specifically on the right side of the door (hinge side when facing the range)
• ✔ Door visibly sags, gaps on one side, or won’t latch closed
• ✔ ONLY problem is door alignment, door not closing flush, or hinge visibly bent or broken

Not sure? Send us your model number — we’ll confirm before you order.

🔧 Common Symptoms

• Oven door sags or hangs lower on one side — most common complaint
• Door won’t close fully or latch properly
• Visible gap between door and range frame when closed
• Heat escaping from around the door during baking
• Door feels loose or wobbles when opened
• Hinge arm visibly bent, cracked, or broken on inspection

✔ If these symptoms match, the WS01L14674 right side door hinge is the most likely failed component.

✔ In most cases, replacing this hinge restores full door alignment and a tight seal immediately.

📦 Part Details

• Part Number: WS01L14674
• Type: Oven door hinge — right side, pivot-arm style
• Replaces: OEM direct-fit hinge — supersedes WB10X21056, WS01L11503, WB10X26464, 222D9737P006 (no modification required)
• Brands: GE, GE Profile, GE Café
• Position: Right side only — if both hinges are worn, order two

⚙️ Installation

Skill Level: MODERATE — 20–30 minutes. Disconnect power at the breaker before beginning. Open the oven door fully and locate the hinge locks on each hinge arm — flip them to the locked position, then lift the door straight up and off the range to remove it. Remove the screws securing the old right hinge, install the new WS01L14674, and reinstall the door by aligning the hinge arms with the slots and pressing down firmly until they seat. Flip the hinge locks back to the open position and test door operation before restoring power.

💡 Pro Tip

🔗 Model Hub Pages

Find part compatibility guides and repair resources for your specific model: CS980ST8SS, JCGS650SEF3SS, JCGS650SEF4SS, P2S920SEF5SS, CBC980ST6SS, CBC980ST7SS, CCGB500P2M1S1, CCGB500P3M1D1, CCS975SD4SS, EGP750ES0A, JCGS750SEF3SS, JCGS750SEF4SS, JCGS750SEF5SS, JCGS750SEF6SS, JGS750SEF1SS, PC2S920EEJ1ES, PC2S920EEJ2ES, PC2S920EEJ3ES, PC2S920SEF4SS, PC2S920SEF5SS, PC2S920SEJ1ES, PCGS920EEJ1ES, PCGS920EEJ2ES, PCGS920EEJ3ES, PCGS920SEF2SS, PCGS920SEF4SS, PCGS920SEF5SS, PCGS920SEJ1ES, PCS940DM2WW, PCS940DM3WW.