GE Dryer Timer WW02F00565 — Fix Dryer That Won't Start, Stop or Complete a Cycle
When a GE dryer won’t start, runs continuously without stopping, or fails to advance through its drying cycle, the mechanical timer is almost always the root cause. In most GE and Hotpoint electric dryers, the timer controls the entire cycle sequence — start, heat, cool-down, and shutoff. When it fails, the dryer may not respond to the start command, run indefinitely without shutting off, or stop mid-cycle before clothes are dry. ⚡ Common failure point in GE-built GTD and GTX series dryers. Part WW02F00565 is the current genuine OEM replacement that restores full cycle control with a direct plug-in installation — no rewiring required, superseding WE04X24550, WE04X24549, 234D2377P004, TMD14M30, and E190094.
GE Dryer WW02F00565
Is This the Right Part?
Confirm the complete model number before ordering. Similar parts may use different connectors, dimensions, hose positions, electrical ratings, or mounting points.
- ✔ Your GE or Hotpoint dryer powers on but won’t start a cycle or won’t stop when the cycle ends
- ✔ The door switch and thermal fuse have been confirmed good
- ✔ The drive motor runs when manually bypassed — confirming the motor is not the issue
- ✔ ONLY problem is cycle control — the timer dial turns but the dryer does not respond correctly
- Dryer won’t start when the timer is set and the start button is pressed
- Dryer runs continuously and never shuts off at the end of the cycle
- Timer dial turns but dryer does not advance through heat and cool-down stages
- Dryer stops mid-cycle before clothes are fully dry
- No heat during the timed portion of the cycle despite the element being good
- Dryer starts but immediately stops after a few seconds
- Part Number: WW02F00565
- Type: Mechanical Dryer Cycle Timer — controls start, heat, cool-down, and shutoff sequence
- Replaces: WE04X24550, WE04X24549, 234D2377P004, TMD14M30, E190094 — no modification required
- Brands: GE, General Electric, Hotpoint
Before pulling the old timer, use a marker or tape to note the exact position of the timer knob on the shaft. GE dryer timers use a D-shaped shaft and the knob must be reinstalled in the correct orientation for the cycle markings to align with the actual timer cam positions. Getting this wrong means the “Perm Press” setting runs a “Delicate” cycle — a small detail that causes a lot of callbacks.
Part Details
Use a qualified technician when diagnosis or installation is outside your experience. Gas parts should be installed by a licensed technician.
Verified Compatible Models
GTD42EAAJ1WW, GTD42EAAJ2WW, GTD42EAMJ2WW, GTD42EBMK0WW, GTD42GAMJ0WW, GTD42GAMJ1WW, GTD42GAMJ2WW, GTD42GASJ2WW, GTD42GBMK0WW, GTD47EBAL0DG, GTX42EASJ2WW
Fitment reminder: Match the complete model number, including suffixes and revision digits, before ordering.
This is the correct fix if ALL of the following are true:
Not sure? Send us your model number — we’ll confirm before you order.
✔ If these symptoms match, this is the most likely failed component in the system.
✔ In most cases, replacing this timer restores full cycle control immediately.
Skill Level: Easy to Moderate — 20 to 40 minutes. Disconnect power before servicing. Remove the dryer control panel by releasing the clips or screws at the top of the console. Photograph the wiring harness connections on the old timer before removal, then transfer the wiring connector to the new timer in the same position. Secure the new timer in the panel, reassemble the console, and run a full timed cycle to confirm correct start, heat, and shutoff operation.
Confirmed compatible with GTD42EAAJ1WW, GTD42EAAJ2WW, GTD42EAMJ2WW, GTD42EBMK0WW, GTD42GAMJ0WW, GTD42GAMJ1WW, GTD42GAMJ2WW, GTD42GASJ2WW, GTD42GBMK0WW, GTD47EBAL0DG, GTX42EASJ2WW, SGE47N5XNSBH00, SGG47N5XNBAB00, SGN47N5XNBAB00. Contact us to verify your model number before ordering.
Buy Online Pick Up In-Store
Kitchener, Ontario N2E 1W8
All brand names are the property of their respective owners and are used for compatibility reference only.
- Choosing a selection results in a full page refresh.
