GE LMH79104WBAB02 Washer Not Spinning: Safe Checks and Drive Parts
Is your GE LMH79104WBAB02 washer not spinning? Start by separating a spin problem from a drain problem. Check whether water leaves the tub, whether the lid locks or latches, whether the basket moves during a Drain & Spin cycle, and whether the washer makes unusual noises. A washer that drains but leaves clothes soaking wet may have a motor-and-drive issue, but the symptom alone does not identify one guaranteed failed part.
For this verified GE washer fitment, the available motor-and-drive parts are the WG04L05385 Drive Belt, WW01F01756 BELT DRIVE (POLYV BELT 6:1), and WW01F01784 Washer Motor Clutch. Before buying, read the appliance model label and compare the replacement part number with the number on the part you are replacing or with your service information.
What should you check first when the GE washer will not spin?
Begin with simple observations rather than removing parts:
- Check for standing water. If water remains in the tub, the washer may not be completing the drain portion of the cycle. That is different from a washer that drains normally but does not rotate the basket.
- Check the load. Stop and redistribute clothing if the load is tightly packed, very heavy, or gathered on one side. An overloaded or unbalanced load can interrupt or limit spin performance.
- Observe the lid lock or latch. Note whether it engages when the spin cycle begins. Do not bypass, defeat, or tamper with a lid-safety device.
- Try the appropriate cycle. If your washer provides a separate Drain & Spin cycle, observe whether it drains and attempts to spin. A different result can help distinguish a cycle, load, or component concern.
- Note sounds and indicators. Record any humming, clicking, grinding, or squealing. Also note flashing lights or displayed error information for a qualified technician.
Disconnect power before inspecting, cleaning around, or accessing any washer component. Do not reach into a moving basket, work around exposed wiring while energized, or continue operating the appliance if there is a burning smell, smoke, damaged cord, or visible water near electrical parts.
Could a drive belt cause this GE washer not to spin?
Yes, a drive belt is one possible cause when the washer motor operates but the basket does not transfer motion correctly. A belt may be worn, damaged, loose, or otherwise unable to drive the washer as intended. However, similar symptoms can come from other components or from a condition outside the drive system, so a belt should not be ordered solely because the washer is leaving clothes wet.
The verified hub lists two belt products for the GE LMH79104WBAB02:
- WG04L05385 Drive Belt — part number WG04L05385.
- GE BELT DRIVE (POLYV BELT 6:1) — part number WW01F01756.
These are separate verified product listings. Do not assume that two belt listings are interchangeable just because both are described as drive belts. Confirm the exact part number required for your model and configuration before checkout.
Could the motor clutch be responsible for the missing spin?
It is also possible. The motor clutch is part of the washer motor-and-drive system, and a problem in that area may prevent the basket from spinning even when the washer fills or agitates. Unusual clicking, humming, or other drive-related noise may be useful information, but sound alone cannot confirm a clutch failure.
The verified fitment for this model includes the WW01F01784 Washer Motor Clutch. If inspection or diagnosis points to the clutch, compare the existing part and documentation with part number WW01F01784 before ordering. Avoid replacing multiple components as a guess when the cause has not been established.
Why can several components create the same spin symptom?
“Not spinning” describes an observed result, not a complete diagnosis. The washer may fill, agitate, drain, lock the lid, or stop at different points depending on the underlying issue. A belt concern and a motor-clutch concern can both appear as a basket that does not spin. A drain condition, lid-lock condition, unbalanced load, control issue, or another appliance problem can also affect whether the washer proceeds through spin.
That is why the most useful troubleshooting details are specific:
- Does the GE washer fill normally?
- Does it agitate?
- Does it drain fully?
- Does the lid lock or latch?
- Does the basket move at all during spin?
- Does a separate Drain & Spin cycle behave differently?
- Are clothes left soaking wet?
- Did the issue begin after an unusually large or unbalanced load?
- Are any lights flashing or codes displayed?
These observations can help a qualified repair professional narrow the issue without treating one symptom as proof of a particular failed part.
Where can you find the verified parts for GE model LMH79104WBAB02?
Use the verified GE washer LMH79104WBAB02 parts hub to review the model-specific motor-and-drive options:
These products are verified for the listed GE LMH79104WBAB02 washer fitment in the supplied model hub. Fitment verification does not determine which component has failed. Confirm the model label on the appliance and the part number before ordering.
When should you stop troubleshooting and request service?
Request qualified service if the washer has exposed electrical damage, a burning odor, smoke, repeated tripping of a breaker, leaking near electrical components, a damaged power cord, or a lid-safety problem. Service is also appropriate when the washer will not drain, makes severe grinding noises, or requires internal access that you cannot perform safely. Keep notes about the cycle, load, sounds, water level, lid-lock behavior, and any displayed indicators so the technician can evaluate the symptom more efficiently.
Frequently asked questions about the GE LMH79104WBAB02 not spinning
Does a washer that drains but does not spin always need a belt?
No. A belt is one possible cause. The motor clutch and other conditions can produce a similar result.
Should I order both verified belts?
Not automatically. They are separate listings. Confirm the required part number for your appliance configuration before ordering.
Can wet clothes prove that the motor clutch failed?
No. Wet clothes confirm that the cycle did not remove enough water, but they do not identify the failed component.
What information should I have before buying?
Have the full appliance model, GE LMH79104WBAB02, the appliance type, washer symptoms, and the suspected or removed part number. Recheck the model label and part number before checkout.