⚠ This part has been superseded by a newer OEM part number.
DC66-00470A has been replaced by XPart Kit. We recommend ordering the current part for guaranteed fit and full lifespan.
Order XPart Kit Instead →Washer Vibrating or Walking? Front Shock Absorber DC66-00470A – Fix Spin Instability Fast
If your Samsung front-load washer shakes violently, walks across the floor, or bangs during the spin cycle, a worn shock absorber is the most common cause. In most Samsung front-load washers, the drum is suspended by front and rear shock absorbers that dampen movement during high-speed spins. When the front shocks fail, the drum loses damping support — causing excessive vibration, loud banging, and premature wear on the drum bearings and spider arm. ⚡ Common failure point in Samsung-built front-load washers after 3–5 years of use. Part DC66-00470A is the genuine OEM front shock absorber that restores drum stability and eliminates spin-cycle vibration immediately.
❓ Is This the Right Part?
This is the correct fix if ALL of the following are true:
- ✔ Washer powers on and fills/drains normally
- ✔ Wash and rinse cycles run without issue
- ✔ No error codes related to motor or control board
- ✔ ONLY problem is excessive vibration, banging, or movement during spin
Not sure? Send us your model number — we'll confirm before you order.
🔧 Common Symptoms
- Washer shakes violently or walks across the floor during spin
- Loud banging or thumping noise at high spin speeds
- Drum visibly hitting the cabinet during spin cycle
- Vibration worsens with heavier loads or higher spin speeds
✔ If these symptoms match, the front shock absorber is the most likely failed component.
✔ In most cases, replacing DC66-00470A restores smooth, quiet spin operation immediately.
📦 Part Details
- OEM Part Number: DC66-00470A
- XPart SKU: LP0470A
- Type: Front Shock Absorber — dampens drum movement during spin cycles in front-load washers
- Replaces: DC66-00650C, DC66-00650D
- Brands: Samsung
- Position: Front (pair) — sold individually
Replace rear shocks at the same time — DC66-00470B is the rear counterpart. Front and rear shocks wear at similar rates, and replacing both during the same repair prevents a callback and saves labour. Consider the XPart Kit (front + rear set) for the best value.
⚙️ Installation
Skill Level: Moderate — 45–60 minutes. Disconnect power before servicing. Remove the front panel by releasing the door boot seal and unscrewing the lower access panel. Disconnect the old shock absorber from the drum bracket and base frame, then snap the new DC66-00470A into place. Reinstall the panel and run a spin cycle to confirm stability.
✓ Compatible Models
Confirmed compatible with WF209ANW, WF218ANB, WF330ANW, WF331ANR, WF409ANW, WF42H5100AW, WF42H5200AP, WF42H5500AF, WF42H5700AG, WF455ARGSGR plus additional Samsung front-load models. Contact us to verify your model number before ordering.
✓ Model-Specific Repair Pages
💡 Pro Tip
Shock absorbers wear at similar rates. If the front shocks have failed, the rear shocks (DC66-00470B) are likely close behind. Replacing both sets in one repair visit saves you from pulling the machine apart again in 6 months — and protects the drum bearings from further stress in the meantime. The XPart front + rear kit is the most cost-effective option.
✅Compatibility & Cross Reference
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
Buy Online Pick Up In-Store
Kitchener, Ontario N2E 1W8
- Choosing a selection results in a full page refresh.
