Dishwasher Upper Rack Sliding Out or Falling Off the Rail? Stop Clip WP8565925 – Restore Rail Lock Fast
A broken or missing upper rack stop clip is the most common reason a dishwasher upper rack slides all the way out of the tub, falls off the rail, or won't stay in position when loading and unloading. In most Whirlpool-platform dishwashers, the upper slide rail stop clip is a small plastic retainer that snaps onto the end of the upper rack slide rail and prevents the rack from pulling completely free of the tub. When it cracks or breaks off — typically from repeated impact or age-related brittleness — the rack has no stop point and slides out uncontrolled, dumping dishes and creating a safety hazard. ⚡ One of the highest-volume small hardware failures on Whirlpool, Maytag, KitchenAid, and Amana dishwashers. Part WP8565925 is the genuine OEM replacement that snaps back onto the rail end and restores the rack stop in minutes.
❓ Is This the Right Part?
This is the correct fix if ALL of the following are true:
- ✔ Dishwasher powers on and washes normally
- ✔ Upper rack slide rails are intact and not bent or cracked
- ✔ Upper rack rollers are in good condition and roll smoothly
- ✔ ONLY problem is the rack slides completely out of the tub or has no stop at the end of the rail
Not sure? Send us your model number — we'll confirm before you order.
🔧 Common Symptoms
- Upper rack slides completely out of the dishwasher tub when pulled
- Rack falls off the rail when fully extended for loading
- Missing or visibly broken plastic clip at the end of the upper slide rail
- Rack feels loose or wobbly at full extension with no stop point
✔ If these symptoms match, the stop clip is the correct fix — it is the only component that prevents the rack from exiting the rail.
✔ In most cases, snapping in the new stop clip restores full rack function in under 5 minutes.
📦 Part Details
- Part Number: WP8565925
- Type: Dishwasher Upper Rack Slide Rail Stop Clip — a small plastic retainer that snaps onto the end of the upper rack slide rail to prevent the rack from pulling free of the tub
- Replaces: W10508950, 8270105, 8524581, 8524582, 8562015, 8565920, 8565925, W10082860, W10199682, WP8565925VP, WPW10508950
- Brands: Whirlpool, Maytag, KitchenAid, Amana, Jenn-Air
While you have the upper rack out, inspect the rack rollers and the slide rail adjuster clips at the same time. Rack rollers crack and flatten from heat and age — a worn roller causes the rack to sit unevenly and drag on the rail. If the rollers look flat, cracked, or discoloured, replace them while the rack is already removed to avoid a second repair.
⚙️ Installation
Skill Level: EASY — 5 minutes. No tools required. No need to disconnect power for this repair. Pull the upper rack fully out of the dishwasher. Locate the end of the slide rail where the old clip was. Align the new WP8565925 clip with the rail end and press firmly until it snaps into place. Slide the rack back in and test by pulling it to full extension — it should stop cleanly without coming off the rail.
✓ Compatible Models
Confirmed compatible with a wide range of Whirlpool, Maytag, KitchenAid, Amana, and Jenn-Air dishwashers. Contact us with your model number to verify fitment before ordering.
💡 Pro Tip
Most Whirlpool-platform dishwashers have two upper rack slide rails — one on each side. If one stop clip has broken, the other is likely the same age and condition. Replacing both at the same time costs almost nothing extra and prevents the second clip from failing a week later. Check both rail ends while the rack is out.
✓ Model-Specific Repair Pages
✅Compatibility & Cross Reference
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
Buy Online Pick Up In-Store
Kitchener, Ontario N2E 1W8
- Choosing a selection results in a full page refresh.
