Dishwasher Rack Falling Off Track? Slide Rail Stop Clip WP8565925 – Fix It Fast
A dishwasher rack that slides off its rail or collapses mid-cycle is almost always caused by a broken or missing slide rail stop clip. In most Whirlpool-built dishwashers, the slide rail stop clip is a small but critical component that prevents the upper or lower rack from rolling completely off the rail during loading, unloading, or the wash cycle. When it breaks or goes missing, the rack becomes unstable — it can fall, tip, or derail entirely, potentially damaging dishes, the spray arm, or the rail itself. ⚡ Common wear item on Whirlpool, KitchenAid, Kenmore, and Maytag dishwashers. Part WP8565925 is the genuine OEM replacement clip that snaps back onto the rail end and restores full rack stability immediately.
❓ Is This the Right Part?
This is the correct fix if ALL of the following are true:
- ✔ Dishwasher powers on and runs wash cycles normally
- ✔ The rack rail itself is intact and undamaged
- ✔ Your model number is confirmed compatible (see below)
- ✔ ONLY problem is the rack slides off the rail or is missing its end stop clip
Not sure? Send us your model number — we’ll confirm before you order.
🔧 Common Symptoms
- Upper or lower rack slides completely off the rail when pulled out
- Rack tips or collapses when loaded with dishes
- Rack feels loose or wobbly on one side
- End stop clip is visibly cracked, broken, or missing from the rail
- Rack derails during the wash cycle, blocking the spray arm
- Dishes come out dirty because the rack shifted and blocked water spray
✔ If these symptoms match, this is the correct replacement part.
✔ In most cases, snapping in the new clip restores full rack stability in under 2 minutes.
📦 Part Details
- Part Number: WP8565925
- Replaces: 8270105, 8524581, 8524582, 8562015, 8565920, 8565925, W10082860, W10199682, WP8565925VP
- Type: Dishwasher Rack Slide Rail Stop Clip — OEM
- Brands: Whirlpool, KitchenAid, Kenmore, Maytag, Amana, Jenn-Air, Roper, Estate, Crosley
- Appliance Type: Dishwasher (Undercounter & Portable)
- Condition: Genuine OEM — New
While you have the rack out, inspect the rack wheels / rollers and the rail itself. Cracked or missing wheels are the #1 companion failure to a broken stop clip — if the wheels are worn, the rack will continue to ride poorly even with a new clip. Replacing both at the same time saves a second service call and gets the rack running smoothly again.
⚙️ Installation
Skill Level: Easy — under 5 minutes, no tools required. Disconnect power before servicing if working near electrical components. Pull the rack out fully and locate the open end of the slide rail where the stop clip is missing or broken. Snap the new WP8565925 clip firmly onto the end of the rail until it seats securely. Slide the rack back onto the rails and test by pulling it in and out to confirm it stops correctly at full extension.
✓ Compatible Models
Confirmed compatible with a large number of Whirlpool, KitchenAid, Kenmore, Maytag, Amana, Jenn-Air, Roper, Estate, and Crosley dishwasher models including: DU1055XTVB0, GU2300XTVQ0, MDB7749AWB0, KUDC03IVBL0, GU3200XTVB0, 66513032K110, KUDI01ILBL0, WDF530PAYB0, IUD8000RQ0, and hundreds more. Contact us with your model number to verify fitment before ordering.
💡 Pro Tip
Dishwasher racks have a stop clip on each end of each rail — if one has broken, the clip on the opposite end is under the same age and stress. Ordering a pair now means you’re covered when the second one goes, and you avoid paying shipping twice for a $13 part. It’s the most cost-effective rack repair you can make.
✓ Model-Specific Repair Pages
✅Compatibility & Cross Reference
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
Buy Online Pick Up In-Store
Kitchener, Ontario N2E 1W8
- Choosing a selection results in a full page refresh.
