Menu
Washer Won’t Spin or Drum Not Turning? Inverter Board WG04F13075 – Fix Motor Faults Fast
If your GE or GE Profile front-load washer won’t spin, the drum won’t turn, or you’re seeing motor-related error codes, the inverter board is the most likely cause. In most GE front-load washers, this is caused by a failed inverter board. When it fails, the drive motor receives no power or incorrect signals — leaving the drum unable to agitate, spin, or complete any cycle that requires drum movement. ⚡ Common failure point in GE-built front-load washers. Part WG04F13075 is the genuine OEM replacement that restores full motor drive control and gets your washer spinning reliably again.
❓ Is This the Right Part?
This is the correct fix if ALL of the following are true:
- ✔ Washer has power and the control panel responds normally
- ✔ Door latch, lid switch, and water supply have been confirmed OK
- ✔ Washer fills with water but drum does not agitate or spin
- ✔ ONLY problem is no spin, no drum movement, or motor-related error codes
Not sure? Send us your model number — we’ll confirm before you order.
🔧 Common Symptoms
- Washer fills and drains but drum does not spin or agitate
- Drum turns slowly or intermittently then stops
- Motor error codes displayed (E3, E7, or similar motor fault codes)
- Loud humming from motor area but no drum movement
✔ If these symptoms match, this is the most likely failed component in the system.
✔ In most cases, replacing this inverter board restores normal spin and agitation immediately.
📦 Part Details
- Part Number: WG04F13075
- Type: Motor Inverter Board — converts DC power to variable-frequency AC to control drum motor speed and direction
- Replaces: WG04F12727, WG04F12645, WG04F12012
- Brands: GE, GE Profile
⚠️ Recommended While Repairing:
Inspect the drive motor and motor wiring harness connectors while the inverter board is out — burnt terminals or a failing motor winding are common co-failure points that will damage a new inverter board if not addressed. Also check the stator and rotor for physical damage before reassembling.
Inspect the drive motor and motor wiring harness connectors while the inverter board is out — burnt terminals or a failing motor winding are common co-failure points that will damage a new inverter board if not addressed. Also check the stator and rotor for physical damage before reassembling.
⚙️ Installation
Skill Level: MODERATE — 45–75 minutes. Disconnect power before servicing. Access the inverter board by removing the rear panel of the washer. Photograph all connector positions before disconnecting. Transfer connectors one at a time to the new WG04F13075 board, reassemble the rear panel, restore power, and run a spin-only cycle to confirm operation.
✓ Compatible Models
Confirmed compatible with GFW850SPL2RS, GFW850SPN2RS, GFW650SSN1WW, GFW550SSN1WW, GFW148SSN0WW plus additional GE and GE Profile front-load washer models. Contact us to verify your model number before ordering.
💡 Pro Tip
Check the Motor Before Replacing the Inverter Board:
A shorted or failing drive motor will draw excessive current and burn out a new inverter board within minutes of operation. Before installing WG04F13075, disconnect the motor leads and check motor winding resistance with a multimeter — readings outside the normal range (typically 4–12 ohms per winding) indicate a motor that needs replacement first. Replacing the inverter board on a bad motor is the most common cause of repeat inverter board failures on GE front-loaders.
A shorted or failing drive motor will draw excessive current and burn out a new inverter board within minutes of operation. Before installing WG04F13075, disconnect the motor leads and check motor winding resistance with a multimeter — readings outside the normal range (typically 4–12 ohms per winding) indicate a motor that needs replacement first. Replacing the inverter board on a bad motor is the most common cause of repeat inverter board failures on GE front-loaders.
✅Compatibility & Cross Reference
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
Buy Online Pick Up In-Store
Address
101 Trillium Dr
Kitchener, Ontario N2E 1W8
Kitchener, Ontario N2E 1W8
Phone
Hours
Mon–Fri 9 AM–5 PM • Sat 9 AM–1 PM
- Choosing a selection results in a full page refresh.
