Menu
Washer Won't Power On? GE Power Cord WG04F12012 – Fix No Power Fast
If your GE or Hotpoint washer is completely dead — no lights, no response, no cycle — the power cord is the first component to check. In most GE front-load washers, a damaged or failed power cord prevents the machine from receiving any electrical supply. When it fails, the washer will not power on at all, may trip the breaker repeatedly, or show intermittent power loss. ⚡ Common failure point in GE-built front-load washers. Part WG04F12012 is the genuine OEM replacement that restores full electrical supply and gets your washer running again.
❓ Is This the Right Part?
This is the correct fix if ALL of the following are true:
- ✔ QUALIFIER 1 — washer is completely unresponsive (no lights, no display)
- ✔ QUALIFIER 2 — wall outlet and breaker have been confirmed working
- ✔ QUALIFIER 3 — power cord shows visible damage, burning, or fails continuity test
- ✔ ONLY problem is no power reaching the washer
Not sure? Send us your model number — we'll confirm before you order.
🔧 Common Symptoms
- Washer completely dead — no lights, no display, no response
- Breaker trips immediately when washer is plugged in
- Intermittent power loss mid-cycle
- Visible burn marks, melting, or damage on the cord or plug
✔ If these symptoms match, this is the most likely failed component in the system.
✔ In most cases, replacing this power cord restores normal operation immediately.
📦 Part Details
- Part Number: WG04F12012
- Type: OEM Washer Power Cord / Electrical Supply Cord
- Replaces: WG04F12012 (verify cross-references with your model)
- Brands: GE, Hotpoint, GE Profile
⚠️ Recommended While Repairing:
If your washer lost power suddenly or tripped a breaker, inspect the main control board for burn marks or damage before reassembling — a shorted board can destroy a new cord. Consider checking the GE Inverter Board WG04F13075 if the washer also has spin or motor fault issues.
If your washer lost power suddenly or tripped a breaker, inspect the main control board for burn marks or damage before reassembling — a shorted board can destroy a new cord. Consider checking the GE Inverter Board WG04F13075 if the washer also has spin or motor fault issues.
⚙️ Installation
Skill Level: EASY — 10–20 minutes. Disconnect power before servicing. Unplug the old cord from the washer's terminal block at the rear access panel, noting wire positions. Connect the new WG04F12012 cord to the same terminals, secure the strain relief, and restore power to test.
✓ Compatible Models
Confirmed compatible with select GE and Hotpoint front-load washer models. Contact us to verify your model number before ordering.
💡 Pro Tip
Check the Outlet First:
Before replacing the cord, plug a known working appliance into the same outlet to rule out a dead receptacle or tripped GFCI. If the outlet is confirmed live and the washer still won't power on, the cord is the next logical replacement — and WG04F12012 is the OEM fix.
Before replacing the cord, plug a known working appliance into the same outlet to rule out a dead receptacle or tripped GFCI. If the outlet is confirmed live and the washer still won't power on, the cord is the next logical replacement — and WG04F12012 is the OEM fix.
✅Compatibility & Cross Reference
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
Buy Online Pick Up In-Store
Address
101 Trillium Dr
Kitchener, Ontario N2E 1W8
Kitchener, Ontario N2E 1W8
Phone
Hours
Mon–Fri 9 AM–5 PM • Sat 9 AM–1 PM
- Choosing a selection results in a full page refresh.
