GE Washer Won't Spin or Showing Speed Errors? Speed Sensor WW01F01707 – Fix Erratic Drum & Spin Faults Fast
When your GE washer won't spin, agitates erratically, displays spin speed error codes, or the drum movement seems uncontrolled, the speed sensor (hall sensor / tachometer) is the primary component to test. In GE top-load washers, the speed sensor detects the rotational speed and position of the drive motor or drum and sends real-time feedback to the main control board for precise cycle timing, motor speed regulation, and fault detection. When it fails, the control board loses motor feedback entirely — the washer may refuse to spin, run at incorrect speeds, throw error codes, or stop mid-cycle as a protective response. ⚡ Common failure point in GE top-load washers — especially after wiring harness damage, corrosion, or motor-related events. Part WW01F01707 is the genuine OEM replacement that restores accurate motor speed feedback, clears speed-related error codes, and returns the washer to full spin and agitation control.
❓ Is This the Right Part?
This is the correct fix if ALL of the following are true:
- ✔ Washer powers on and the control panel responds normally
- ✔ Water fills and drains correctly — only spin or agitation is affected
- ✔ Speed-related error code is present, OR drum movement is erratic or absent
- ✔ Drive motor has been confirmed functional — the sensor, not the motor, is the fault
Not sure? Send us your model number — we'll confirm before you order.
🔧 Common Symptoms
- Washer won't spin — drum sits still during spin cycle
- Spin speed error code displayed on control panel
- Drum agitates or spins erratically — inconsistent speed or direction
- Washer stops mid-cycle with no error, or resets repeatedly during spin
✔ If these symptoms match, this is the most likely failed component in the system.
✔ In most cases, replacing this speed sensor restores normal spin and agitation immediately.
📦 Part Details
- Part Number: WW01F01707
- Type: Washer Speed Sensor (Hall Sensor / Motor Sensor / Tachometer Sensor)
- Replaces: 233D2227P001
- Brand: GE
- Application: Drive motor speed and position feedback to main control board
While the sensor is accessible, inspect the wiring harness connector for corrosion, bent pins, or heat damage — a damaged connector is a common cause of speed sensor failure and will kill the new sensor if not addressed. Also check the drive motor for unusual resistance or bearing noise while you have access.
⚙️ Installation
Skill Level: MODERATE — 20–40 minutes. Disconnect power before servicing. Access the speed sensor by removing the washer cabinet or rear panel depending on model. The sensor mounts to the drive motor or stator assembly — disconnect the wiring harness, remove the mounting screw(s), and swap the sensor. Reconnect the harness, reassemble, and run a spin cycle to confirm the error code clears and drum speed is consistent.
✓ Compatible Models
Confirmed compatible with GTW220BMK0WW, GTW220BMK1WW, GTW330BMK0WW, GTW330BMK1WW, GTW460BMK0WW, GTW460BMK1WW, GTW465BMK0WS, GTW465BMK1WS, GTW485BMK0WS, GTW485BMK1WS, GTW680BMK0DG, GTW680BMK0WS, MTW200BMK0WW. Contact us to verify your model number before ordering.
✓ Model-Specific Repair Pages
💡 Pro Tip
Before ordering, use a multimeter to check continuity on the speed sensor wiring harness from the sensor connector to the control board connector. An open circuit in the harness will produce identical symptoms to a failed sensor — and a $5 wire repair beats a $43 sensor replacement. If the harness checks out and the sensor reads out of spec, this is the correct part.
✅Compatibility & Cross Reference
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
Buy Online Pick Up In-Store
Kitchener, Ontario N2E 1W8
- Choosing a selection results in a full page refresh.
