GE Dryer Squealing or Grinding? WW02F00762 Drum Top Bearing — Fix Drum Noise Fast
When your GE dryer produces a high-pitched squeal, grinding, or scraping noise during the dry cycle, a worn drum top bearing is the most common cause. In GUD, MCL, MCLC, MKTG, and CLM series GE stackable and front-load dryers, the drum top bearing supports the front-top edge of the drum and allows it to rotate smoothly. When the bearing wears flat or cracks, the drum loses its support point and grinds against surrounding components — and the noise worsens with every cycle. ⚡ One of the most common noise failures in GE stackable dryers. Part WW02F00762 is the genuine OEM replacement — superseding 234D2614P001 — and restores quiet, smooth drum rotation.
❓ Is This the Right Part?
This is the correct fix if ALL of the following are true:
- ✔ Dryer powers on and heats normally
- ✔ Drum rotates — motor and belt are functioning
- ✔ Noise is present during the drum rotation phase, not just at startup
- ✔ Drum feels rough or resistant when turned by hand with power off
- ✔ ONLY problem is squealing, grinding, or scraping noise during the dry cycle
Not sure? Send us your model number — we'll confirm before you order.
🔧 Common Symptoms
- High-pitched squealing or squeaking noise during the dry cycle — most common complaint
- Grinding or scraping sound that worsens as the dryer heats up
- Noise changes pitch or intensity as the drum spins
- Drum feels rough or resistant when turned by hand
- Visible wear, scoring, or flattening on the bearing surface
- Noise has progressively worsened over multiple cycles
✔ If these symptoms match, this is the most likely failed component in the system.
✔ In most cases, replacing the drum top bearing restores quiet, smooth drum rotation immediately.
📦 Part Details
- Part Number: WW02F00762
- Type: Drum top bearing — front drum support, GE OEM
- Replaces: OEM direct-fit bearing — supersedes 234D2614P001 (no modification required)
- Brands: GE, Mabe, CLG, GUD, MCL, MCLC, MKTG series
With the drum already removed to access the top bearing, inspect the drum felt seal and rear drum bearing — both wear at a similar rate and cause identical noise symptoms. Replacing all three in one visit saves a second full teardown and eliminates the next noise complaint before it starts.
⚙️ Installation
Skill Level: MODERATE — 45–75 minutes. Disconnect power before beginning. Access to the drum top bearing requires removing the dryer top panel and drum — support the drum carefully when removing it to avoid damaging the door seal or front bearing. Install the new bearing, reassemble in reverse order, and run a short no-heat cycle to confirm quiet, smooth drum rotation before returning the unit to service.
💡 Pro Tip
The drum top bearing and drum felt seal wear at similar rates — if the bearing is gone, the seal is likely close behind. With the drum already out, replacing the felt seal costs 15 extra minutes and eliminates the next noise complaint before it starts. Ask us for the compatible felt seal part number for your model.
Model hub pages: GUD27ESSM1WW, GUD27ESSM0WW, GUD27ESPM1DG, GUD27ESPM0DG, GUD27GSSM1WW, GUD27GSSM0WW, GUD57EEMT0DG, MCL1540EEBBX03, MCL1540EEBBX04, MCL1740GSBB01, MCL1740GSBB03, MCL1740GSBB10, MCL2040GSBB00, MCLC1740GSBB00, MCLC1740GSBB01, MCLC2040GSBB00, MKTG15GNAWB10, MKTG15GNAWB20, GTUP270PSDG00, GTUP270GMWM02, CLMG70204BBB00, CLMG70204DBB00, CLME70204BBB00, CLME77014BFU00, CLME77014DFU00
✓ Model-Specific Repair Pages
✅Compatibility & Cross Reference
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
Buy Online Pick Up In-Store
Kitchener, Ontario N2E 1W8
- Choosing a selection results in a full page refresh.
