Frigidaire Dryer Drive Belt 134719300, Replaces 137315300, 7134719300

Is This the Right Part?

✅ Cross Reference Information

Common Symptoms

• Dryer won't tumble — drum doesn't spin
• Motor runs but drum doesn't turn
• Dryer won't start (belt switch activated on some models)
• Squealing or squeaking noise during operation
• Chirping noise when dryer runs
• Thumping or rumbling noise
• Belt slipping — intermittent tumbling
• Burning rubber smell
• Dryer stops mid-cycle
• Drum turns slowly or struggles
• Visible belt damage — cracked, frayed, or broken
• Clothes not drying (drum not spinning)
• Loud noise when dryer starts
• Belt came off drum
• Dryer runs but clothes stay wet
• Glazed belt — shiny smooth surface causing slipping
• Belt stretched — loose and slipping

Check Before Replacing

• Confirm the motor runs — if the dryer is completely dead, the issue is electrical, not the belt
• Spin the drum by hand with the door open — if it spins freely with zero resistance, the belt is broken
• Inspect the idler pulley while the drum is out — a seized or worn idler is often what caused the belt to fail
• Check the drum support rollers for flat spots or wear — worn rollers cause squealing that mimics a belt issue

Pro Tip

Part Details

Installation Notes

• Unplug the dryer
• from the electrical outlet to ensure complete power disconnection.
• Pull the dryer away from the wall
• to provide adequate working space for accessing the rear or front panel.
• Remove the lint screen
• from the lint trap opening.
• Determine the dryer panel configuration.
• Some dryers require front panel removal, while others require rear panel removal to access the drum and belt. Consult the service manual for your specific model if uncertain.
• For front-panel access models:
• Remove the screws along the top edge of the front panel (typically 2-4 screws hidden under the lint trap opening). Lift the top panel up and prop it open or remove it completely.
• Remove the front panel
• by locating and removing the screws that secure it (typically 4-6 screws along the sides or bottom). Disconnect any wire harness connectors attached to the door switch. Carefully pull the front panel away and set it aside.
• For rear-panel access models:
• Remove the screws around the perimeter of the rear panel (typically 8-12 screws). Carefully pull the rear panel away and set it aside.
• Take multiple photos
• of the belt routing before removal. Document how the belt wraps around the drum, passes over the idler pulley, and connects to the motor pulley. This is critical for proper reassembly.
• Locate the drive belt
• wrapped around the drum. It should be visible once the front or rear panel is removed.
• Release tension on the belt
• by pushing the idler pulley toward the motor. This releases the belt tension and allows you to slip the belt off the motor pulley.
• Remove the old belt
• from the motor pulley, idler pulley, and drum. Pull it out of the dryer cabinet.
• Inspect the old belt
• for visible damage such as cracks, fraying, glazing (shiny smooth surface), stretching, or breaks. This confirms the diagnosis.
• Inspect the drum for debris or damage.
• Clean the drum surface where the belt rides with a damp cloth to remove lint, fabric softener residue, or debris.
• Inspect the idler pulley
• for wear, damage, or rough rotation. Spin the pulley by hand—it should rotate smoothly and quietly. If the pulley is worn or damaged, replace it along with the belt.
• Inspect the motor pulley
• for wear, damage, or debris. Clean the pulley with a cloth if necessary.
• Unpack the new 134719300 drive belt
• from its packaging. Handle carefully to avoid twisting or kinking the belt.
• Compare the new belt to the old one
• to verify the length, width, and overall appearance match. Ensure you have the correct replacement part.
• Position the new belt around the drum.
• The ribbed side (grooved side) of the belt should face toward the drum surface. The smooth side should face outward.
• Verify the belt is centered on the drum
• and not twisted or kinked.
• Route the belt under the drum
• so both ends hang down toward the motor and idler pulley area.
• Thread the belt around the idler pulley.
• The belt should wrap around the idler pulley in a way that creates tension when the pulley is released.
• Thread the belt around the motor pulley.
• Refer to your photos to verify the correct routing path.
• Pull the idler pulley toward the motor
• to create slack in the belt, then position the belt onto the motor pulley.
• Release the idler pulley slowly
• to allow it to tension the belt. The belt should be tight and properly seated on all pulleys.
• Verify the belt is properly routed
• by comparing it to your photos. The belt should wrap around the drum, pass over the idler pulley, and connect to the motor pulley without twists or misalignment.
• Manually rotate the drum
• by hand to verify the belt moves smoothly and doesn't slip off any pulleys. The drum should rotate freely without binding.
• Verify the belt tension
• by pressing on the belt between the drum and motor pulley. It should have moderate tension—not too loose (which causes slipping) or too tight (which causes excessive wear).
• Reinstall the front or rear panel
• by aligning it with the dryer cabinet and securing all screws. Reconnect any wire harness connectors to the door switch.
• Reinstall the top panel
• (if removed) by lowering it into position and securing the screws.
• Reinstall the lint screen
• in the lint trap opening.
• Push the dryer back into position
• against the wall.
• Plug the dryer back in
• and restore power.
• Run a test cycle
• (without clothes) on a timed dry cycle for 5-10 minutes to verify proper belt operation.
• Listen for unusual noises
• during the test cycle. The dryer should run quietly without squealing, squeaking, or thumping sounds.
• Verify the drum rotates smoothly
• and consistently throughout the test cycle. Open the door briefly during operation to verify the drum is turning.
• Verify the dryer heats properly
• during the test cycle. The exhaust air should be warm within 2-3 minutes of starting.
• If the drum does not rotate
• , turn off the dryer and verify the belt is properly seated on all pulleys and not twisted or kinked.
• If squealing or squeaking noises occur
• , the belt may be misaligned or the idler pulley may be worn. Verify the belt routing and inspect the idler pulley.
• If the belt slips off during operation
• , the belt may be too loose or the idler pulley may not be tensioning properly. Verify the belt routing and idler pulley function.
• Run a full drying cycle
• with a typical load of clothes to confirm the repair is complete and the dryer operates normally.
• Safety Notes:
• Always unplug the dryer before working on it. The drum is heavy—use caution when removing or reinstalling panels to avoid pinching fingers or dropping the drum. Never operate the dryer without the drive belt installed—this can damage the motor and create safety hazards. Ensure proper belt routing to prevent slipping or premature wear.

Verified Compatible Models

BAQE7073KW0, BAQE7077KB0, BAQE7077KW0, BAQG7073KW0, BAQG7077KB0, BAQG7077KW0, CAQE7001LW0, CAQE7001LW1, CAQE7011KB0, CAQE7011KW0, CAQE7011LW0, CAQE7017KW0, CAQE7021LW0, CAQE7021LW1, CAQE7072LA0, CAQE7072LR0, CAQE7072LW0, CAQE7073KB0, CAQE7073KW0, CAQE7077KA0, CAQE7077KB0, CAQE7077KN0, CAQE7077KR0, CAQE7077KW0, CDE4500KW0, CDE4700LB0, CDE4700LW0, CDE4700LW1, CDE7300RW0, CDE7400QW0, CDE7500KB0, CDE7500KR0, CDE7500KW0, CDE7700LR0, CDE7700LW0, CDE7700LW1, EFMC417SIW0, EFMC527UIW0, EFMC527UIW1, EFMC527UIW2, EFMC527UTT0, EFMC527UTT1, EFMC527UTT2, EFMC617SIW0, EFMC617STT0, EFMC627UIW0, EFMC627UIW1, EFMC627UIW2, EFMC627UTT0, EFMC627UTT1, EFMC627UTT2, EFME417SIW0, EFME427UIW0, EFME427UIW1, EFME427UIW2, EFME517SIW0, EFME517STT0, EFME527UIW0, EFME527UIW1, EFME527UIW2, EFME527UTT0, EFME527UTT1, EFME527UTT2, EFME617SIW0, EFME617STT0, EFME627UIW0, EFME627UIW1, EFME627UIW2, EFME627UTT0, EFME627UTT1, EFME627UTT2, EFMG417SIW0, EFMG427UIW0, EFMG427UIW1, EFMG517SIW0, EFMG517STT0, EFMG527UIW0, EFMG527UIW1, EFMG527UTT0, EFMG527UTT1, EFMG617SIW0, EFMG617STT0, EFMG627UIW0, EFMG627UIW1, EFMG627UTT0, EFMG627UTT1, EIED50LIW0, EIED50LIW1, EIED50LIW2, EIED55HIW0, EIED55HMB0, EIED55IKG0, EIED55IRR0, EIMGD55IIW2, EIMGD55IIW4, EIMGD55IIW5, EIMGD55IMB2, EIMGD55IMB4, EIMGD55IMB5, EIMGD55IRR2, EIMGD60JIW0, EIMGD60JIW2, EIMGD60JIW3, EWMED65HIW0, EWMED65HSS0, EWMED65HTS0, EWMED70JIW0, EWMED70JIW2, EWMED70JIW3, EWMED70JIW4, EWMGD65HIW0, EWMGD65HIW1, EWMGD65HIW2, FAQE7001LW0, FAQE7001LW1, FAQE7011KB0, FAQE7011KR0, FAQE7011KW0, FAQE7017KA0, FAQE7017KB0, FAQE7017KN0, FAQE7017KR0, FAQE7017KW0, FAQE7021LW0, FAQE7072LA0, FAQE7072LN0, FAQE7072LR0, FAQE7072LW0, FAQE7073KA0, FAQE7073KB0, FAQE7073KN0, FAQE7073KR0, FAQE7073KW0, FAQE7077KA0, FAQE7077KB0, FAQE7077KN0, FAQE7077KR0, FAQE7077KW0, FAQE7111LW0, FAQE7111LW1, FAQG7001LW0, FAQG7001LW1, FAQG7011KB0, FAQG7011KR0, FAQG7011KW0, FAQG7017KA0, FAQG7017KB0, FAQG7017KN0, FAQG7017KR0, FAQG7017KW0, FAQG7021LW0, FAQG7072LA0, FAQG7072LN0, FAQG7072LR0, FAQG7072LW0, FAQG7073KA0, FAQG7073KB0, FAQG7073KN0, FAQG7073KR0, FAQG7073KW0, FAQG7077KA0, FAQG7077KB0, FAQG7077KN0, FAQG7077KR0, FAQG7077KW0, FAQG7111LW0, FAQG7111LW1, FFQE5000QW0, FFQE5000QW1, FFQE5100PW0, FFQE5100PW1, FFQG5000QW0, FFQG5000QW1, FFQG5000QW2, FFQG5000QW3, FFQG5100PW0, FFRE1001PW0, FFRG1001PW0, FFRG1001PW1, FFSE5115PA0, FFSE5115PA1, FFSE5115PW0, FFSE5115PW1, FFSE5115PW2, FFSE5115PW3, FFSG5115PA0, FFSG5115PW0, GLEQ2170KE0, GLEQ2170KS0, GLGQ2170KE0, GLGQ2170KS0, LAQE6000LW0, LAQE7000LW0, LAQE7011KB0, LAQE7011KW0, LAQE7077KR0, LAQE7077KW0, LAQE8000LW0, LAQG6000LW0, LAQG7000LW0, LAQG7011KB0, LAQG7011KW0, LAQG7077KR0, LAQG7077KW0, LAQG8000LW0, SAGQ7070KS0, BKQE7017KT0, BKQE7071MT0, CAQE7014KA0, CAQE7014KN0, CARE1011MW0, CARE1011MW1, CARE4044MW0, CARE4044MW1, CASE7021NW0, CASE7021NW2, CASE7021NW3, CASE7073LA0, CASE7073LR0, CASE7073LW0, CASE7074NA0, CASE7074NA2, CASE7074NA3, CASE7074NR0, CASE7074NR2, CASE7074NR3, CASE7074NW0, CASE7074NW2, CASE7074NW3, CDE4701QW0, CDE7400QW1, CDEC450KW0, CDEC750KW0, CDG4500KW0, CDG4700LB0, CDG4700LW0, CDG4700LW1, CDG4701QW0, CDG7300RW0, CDG7400QW0, CDG7500KB0, CDG7500KR0, CDG7500KW0, CDG7700LW0, CDG7700LW1, CFQE4000QW0, CFQE5000QW0, CFQE5000QW1, CFQE5100PW0, CFQE5100PW1, CFQE5100PW2, CFQE5100PW3, CFRE1001PW0, CFSE5100QA0, CFSE5115PA0, CFSE5115PA1, CFSE5115PW0, CFSE5115PW1, DAQE7077KW0, DAQG7077KW0, EFMC517SIW0, EFMC517STT0, EIED5CHIW0, EIED5CHMB0, EIGD50LIW0, EIGD50LIW1, EIGD55HIW0, EIGD55HIW1, EIGD55HIW2, EIGD55HMB0, EIGD55HMB2, EIGD55IKG0, EIGD55IKG1, EIGD55IKG2, EIGD55IRR0, EIGD55IRR1, EIGD55IRR2, EIMED55IIW0, EIMED55IIW1, EIMED55IIW2, EIMED55IIW3, EIMED55IMB0, EIMED55IMB2, EIMED55IRR0, EIMED55QT0, EIMED5CQT0, EIMED60JIW0, EIMED60JIW2, EIMED60JIW3, EIMED60JIW4, EIMED60JIW5, EIMED60JIW6, EIMED60JMB0, EIMED60JRR0, EIMED60LSS0, EIMED60LSS2, EIMED60LSS3, EIMED60LT0, EIMED60LT2, EIMED60LT3, EIMED60LT4, EIMED6CJIW0, EIMED6CJIW2, EIMED6CJIW3, EIMED6CJIW4, EIMED6CJMB0, EIMED6CJRR0, EIMED6CLSS0, EIMED6CLSS2, EIMED6CLSS3, EIMED6CLSS4, EIMED6CLT0, EIMED6CLT2, EIMED6CLT3, EIMED6CLT4, EIMGD55QT0, EIMGD60JMB0, EIMGD60JRR0, EIMGD60LSS0, EIMGD60LSS2, EIMGD60LSS3, EIMGD60LT0, EIMGD60LT2, EIMGD60LT3, EWED65HIW0, EWED65HSS0, EWED65HTS0, EWGD65HIW0, EWGD65HSS0, EWGD65HTS0, EWMED65IMB0, EWMED65IRR0, EWMED6CHIW0, EWMED6CHSS0, EWMED6CHTS0, EWMED6CIRR0, EWMED70JMB0, EWMED70JRR0, EWMED70JSS0, EWMED70JSS2, EWMED70JSS3, EWMED70JSS4, EWMED70JTS0, EWMED7CJIW0, EWMED7CJIW2, EWMED7CJIW3, EWMED7CJIW4, EWMED7CJMB0, EWMED7CJRR0, EWMED7CJSS0, EWMED7CJSS2, EWMED7CJSS3, EWMED7CJSS4, EWMED7CJTS0, EWMGD65HSS0, EWMGD65HSS1, EWMGD65HSS2, EWMGD65HTS0, EWMGD65HTS1, EWMGD65HTS2, EWMGD65IMB0, EWMGD65IMB1, EWMGD65IMB2, EWMGD65IRR0, EWMGD65IRR1, EWMGD65IRR2, EWMGD70JIW0, EWMGD70JIW2, EWMGD70JIW3, EWMGD70JMB0, EWMGD70JRR0, EWMGD70JSS0, EWMGD70JSS2, EWMGD70JSS3, EWMGD70JTS0, FAQE7001LB0, FAQE7011LB0, FAQE7011LW0, FAQE7021LB0, FAQG7001LB0, FAQG7011LB0, FAQG7011LW0, FAQG7021LB0, FARE1011MW0, FARE1011MW1, FARE4044MW0, FARE4044MW1, FARG1011MW0, FARG1011MW1, FARG4044MW0, FARG4044MW1, FASE7021NW0, FASE7021NW2, FASE7021NW3, FASE7073LA0, FASE7073LN0, FASE7073LR0, FASE7073LW0, FASE7073NA0, FASE7073NA2, FASE7073NA3, FASE7073NR0, FASE7073NR2, FASE7073NR3, FASE7073NW0, FASE7073NW2, FASE7073NW3, FASE7074LA0, FASE7074LN0, FASE7074LR0, FASE7074LW0, FASE7074NA0, FASE7074NA2, FASE7074NA3, FASE7074NR0, FASE7074NR2, FASE7074NR3, FASE7074NW0, FASE7074NW2, FASE7074NW3, FASG7021NW0, FASG7021NW2, FASG7021NW3, FASG7073LA0, FASG7073LN0, FASG7073LR0, FASG7073LW0, FASG7073NA0, FASG7073NA2, FASG7073NA3, FASG7073NR0, FASG7073NR2, FASG7073NR3, FASG7073NW0, FASG7073NW2, FASG7073NW3, FASG7074LA0, FASG7074LN0, FASG7074LR0, FASG7074LW0, FASG7074NA0, FASG7074NA2, FASG7074NA4, FASG7074NA5, FASG7074NR0, FASG7074NR2, FASG7074NR3, FASG7074NW0, FASG7074NW2, FASG7074NW3, FRQE7000LW0, FRQG7000LW0, GCEQ2170KE0, GCEQ2170KS0, SGQ2170KS0, ELFE743CAG0, 41781100000, 41781100003, 41781101000, 41781102000, 41781102003, 41781122310, 41781122311, 41784130000, 41784131000, 41784132000, 41788022000, 41791100000, 41791100003, 41791101000, 41791102000

Fitment reminder: Match the complete appliance model number, including suffix or revision where applicable, before ordering.