Dryer Not Spinning? Idler Pulley Assembly 134793511 – Fix Belt Tension Loss Fast
A failed idler pulley assembly doesn't just make noise — it kills drum rotation entirely, leaving clothes soaking wet and your dryer useless. In most Frigidaire-built dryers, this is caused by a failed idler arm and pulley assembly. When it fails, the drive belt loses tension, the drum stops turning, and the dryer runs heat with no airflow — a fire risk if left unaddressed. ⚡ Common failure point in Frigidaire-built dryers. Part 134793511 is the genuine OEM replacement that restores correct belt tension and drum rotation immediately.
❓ Is This the Right Part?
This is the correct fix if ALL of the following are true:
- ✔ Dryer powers on and motor runs normally
- ✔ Heating element and controls work correctly
- ✔ Power supply and door switch confirmed OK
- ✔ ONLY problem is drum not spinning, squealing, or belt slipping off
Not sure? Send us your model number — we'll confirm before you order.
🔧 Common Symptoms
- Dryer drum not rotating at all (no drum movement)
- Squealing, squeaking, or thumping noises during operation
- Drive belt slipping off or losing tension
- Drum rotating slowly or intermittently
- Dryer taking longer than normal to dry clothes
- Drum stopping mid-cycle
- Visible flat spots, cracks, or wear on the pulley wheel
- Idler arm loose or wobbly when drum is manually rotated
✔ If these symptoms match, this is the most likely failed component in the system.
✔ In most cases, replacing this idler pulley assembly restores normal drum operation immediately.
📦 Part Details
- Part Number: 134793511
- Type: Idler Arm & Pulley Assembly (Belt Tensioner)
- Replaces: 134793500, 134793512, 7134793500
- Brands: Frigidaire, Electrolux, Gibson, Kenmore, White-Westinghouse, Kelvinator, Tappan
The idler pulley and drive belt wear together. If your pulley has failed, inspect the belt for fraying, glazing, or cracking — a worn belt on a new pulley causes premature failure and a second labour call. Drum support rollers are also worth checking at the same time. Replacing all three in one visit is the professional standard.
⚙️ Installation
Skill Level: MODERATE — 45–60 min DIY / 30–45 min professional. Disconnect power before servicing. Remove the front or rear panel to access the idler assembly at the base of the cabinet. Photograph belt routing before removal — critical for correct reassembly. Route belt around drum → under idler pulley → around motor pulley. Test belt tension after install: belt should deflect ~0.5–1 inch under moderate pressure.
✓ Compatible Models
Confirmed compatible with 41781100000, 41781101000, 41781102000, BAQE7073KW0, BAQE7077KB0, CAQE7001LW0, CAQE7011KB0, CAQE7011KW0, EFME427UIW0, EFME527UIW0, EFME627UIW0, FAQE7001LW0, FAQE7011KW0, FAQE7077KW0, FAQG7001LW0, FAQG7077KW0, ELFE7337AW0, ELFE7637AW0, ELFG7637AW0, EIMED60JIW0, EIMGD60JIW0 plus hundreds of additional Frigidaire, Electrolux, Gibson, Kenmore, and White-Westinghouse models. Contact us to verify your model number before ordering.
💡 Pro Tip
The idler pulley and drive belt wear together. A worn belt on a new pulley will cause premature failure and a second labour call. Drum support rollers are also worth inspecting at the same time — replacing all three in one visit is the professional standard and saves significant labour cost on a repeat repair.
✅Compatibility & Cross Reference
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
Buy Online Pick Up In-Store
Kitchener, Ontario N2E 1W8
- Choosing a selection results in a full page refresh.
