Dryer Taking Too Long to Dry? Lint Screen 5304529766 – Fix Restricted Airflow Fast

If your Frigidaire or Electrolux dryer is taking multiple cycles to dry a load or overheating mid-cycle, a clogged, torn, or missing lint screen is the most common cause. In most Frigidaire-built dryers, the lint screen is the first line of defence against airflow restriction. When it tears or clogs beyond cleaning, airflow through the drum drops sharply, drying times double, and the thermal limiter trips to prevent overheating. ⚡ High-wear consumable — inspect after every 6 months of use. Part 5304529766 is the genuine OEM replacement that restores full airflow and safe drying performance immediately. Note: this part number has been superseded by 140201067026 — we recommend ordering the current part.

❓ Is This the Right Part?

This is the correct fix if ALL of the following are true:

• ✔ Dryer powers on and drum rotates normally
• ✔ Heating element and thermal fuse are functional
• ✔ Exhaust duct and exterior vent are clear of blockages
• ✔ Dryer completes cycles but clothes remain damp
• ✔ ONLY problem is slow drying, overheating, or a visibly torn, holed, or broken lint screen

Not sure? Send us your model number — we'll confirm before you order.

🔧 Common Symptoms

• Dryer taking 2–3 cycles to fully dry a normal load — most common complaint
• Dryer overheating or shutting off mid-cycle on thermal protection
• Visible tear, hole, or puncture in the lint screen mesh
• Lint screen frame cracked, warped, or broken
• Lint bypassing the filter and accumulating in the exhaust duct
• Burning or musty smell during drying cycle

✔ If these symptoms match, this is the most likely failed component in the system.

✔ In most cases, replacing this lint screen restores full airflow and normal drying times immediately.

📦 Part Details

• Part Number: 5304529766 (superseded — current OEM is 140201067026)
• Type: Dryer Lint Screen / Lint Filter — rigid plastic frame with fine mesh filter surface
• Replaces: 5304513574, 5304534450 (no modification required)
• Brands: Frigidaire, Electrolux

⚙️ Installation Notes

Skill Level: EASY — 2 minutes, no tools required. Disconnect power before servicing the dryer. Locate the lint trap slot in the dryer door opening or top panel depending on your model. Pull the old lint screen straight out of the slot, insert the new screen in the same orientation until it seats fully. Clean the screen after every load by removing lint by hand; wash monthly with warm water and mild dish soap to clear detergent residue — allow to dry completely before reinstalling. Never operate the dryer without the lint screen installed.

✓ Compatible Models

EFMG628WTT00, EFMG627UTT1, EFMG627UTT0, EFMG627UIW1, EFMG627UIW0, EFMG527UTT1, EFMG527UTT0, EFMG527UIW1, EFMG527UIW0, EFMG427UIW1, EFMG427UIW0, EFME628WTT00, EFME627UTT2, EFME627UTT1, EFME627UTT0, EFME627UIW2, EFME627UIW1, EFME627UIW0, EFME527UTT2, EFME527UTT1, EFME527UTT0, EFME527UIW2, EFME527UIW1, EFME527UIW0, EFME427UIW2, EFME427UIW1, EFME427UIW0, EFMC627UTT2, EFMC627UTT1, EFMC627UTT0, EFMC627UIW2, EFMC627UIW1, EFMC627UIW0, EFMC527UTT2, EFMC527UTT1, EFMC527UTT0, EFMC527UIW2, EFMC527UIW1, EFMC527UIW0, EFMC427UIW2, EFMC427UIW1, EFMC427UIW0, EFDG317TIW2, EFDG317TIW1, EFDE317TIW3, EFDE317TIW2, EFDE317TIW1, EFDC317TIW3, EFDC317TIW2, EFDC317TIW1. Contact us to verify your model number before ordering.

💡 Pro Tip