Menu
Oven Running Too Hot or Too Cold? Samsung Oven Temperature Sensor DG32-00004C – Fix Temp Problems Fast
A failed oven temperature sensor causes your Samsung range to run significantly hotter or colder than the set temperature, produce uneven baking results, or display temperature-related error codes — even when the heating element is working fine. In most Samsung ranges and wall ovens, this is caused by a failed RTD temperature sensor — the probe mounted to the rear oven wall that continuously monitors cavity temperature and feeds readings to the control board. When it fails, the control board loses accurate temperature data, causing the oven to overshoot, undershoot, or cycle erratically, and error codes such as SE or E-08 may appear on the display. ⚡ One of the most common and easiest oven repairs on Samsung NE, NX, NV, NQ, and NY series ranges. Part DG32-00004C is the genuine OEM replacement that restores accurate temperature sensing and eliminates error codes immediately.
❓ Is This the Right Part?
This is the correct fix if ALL of the following are true:
- ✔ Range powers on and surface burners work normally
- ✔ Bake and broil elements show continuity (not open)
- ✔ Control board is not displaying unrelated fault codes
- ✔ ONLY problem is oven temperature inaccuracy, uneven baking, or SE/E-08 error codes on the display
Not sure? Send us your model number — we'll confirm before you order.
🔧 Common Symptoms
- Oven running significantly hotter or colder than the set temperature
- Uneven baking — food burns on one side or comes out undercooked
- SE, E-08, or other temperature-related error codes on the display
- Oven cycling on and off erratically or failing to maintain set temperature
✔ If these symptoms match, this is the most likely failed component in the system.
✔ In most cases, replacing this temperature sensor restores accurate oven temperature control and clears error codes immediately.
📦 Part Details
- Part Number: DG32-00004C
- Type: Oven RTD Temperature Sensor (Resistance Temperature Detector) — mounts to rear oven wall
- Replaces: DG32-00004CXP, AP5967723, PS9606608
- Brands: Samsung, Dacor
⚠️ Test Before You Replace:
Before ordering, test the existing sensor with a multimeter — a working DG32-00004C reads approximately 1080–1090 ohms at room temperature. If it reads open circuit or significantly outside that range, replacement is confirmed. If the sensor tests good, the control board may be the actual fault.
Before ordering, test the existing sensor with a multimeter — a working DG32-00004C reads approximately 1080–1090 ohms at room temperature. If it reads open circuit or significantly outside that range, replacement is confirmed. If the sensor tests good, the control board may be the actual fault.
⚙️ Installation
Skill Level: EASY — 15–20 minutes. Phillips screwdriver only. Disconnect power at the breaker before servicing. The sensor is mounted to the rear wall of the oven cavity with two screws — remove the screws, pull the sensor forward, disconnect the wiring harness connector, and connect the new DG32-00004C. Reverse to reinstall, restore power, and run a bake cycle to confirm accurate temperature regulation.
✓ Compatible Models
Confirmed compatible with Samsung NE58F9710WS, NE59J7850WS, NX58H9500WS, NX58M9420SS, NV51K7770SS, NQ70M7770DS, NY58J9850WS plus additional Samsung NE, NX, NV, NQ, NY series ranges and Dacor DOB/DOC/DOP series wall ovens. Contact us to verify your model number before ordering.
💡 Pro Tip
Multimeter Test Takes 2 Minutes — Do It First:
A failed temperature sensor is the most common cause of Samsung oven temperature problems, but a faulty control board causes identical symptoms. Test the sensor at room temperature with a multimeter — it should read 1080–1090Ω. If it's open or wildly off, DG32-00004C is your fix. If it tests good, the control board needs further diagnosis before you order parts.
A failed temperature sensor is the most common cause of Samsung oven temperature problems, but a faulty control board causes identical symptoms. Test the sensor at room temperature with a multimeter — it should read 1080–1090Ω. If it's open or wildly off, DG32-00004C is your fix. If it tests good, the control board needs further diagnosis before you order parts.
✅Compatibility & Cross Reference
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
Buy Online Pick Up In-Store
Address
101 Trillium Dr
Kitchener, Ontario N2E 1W8
Kitchener, Ontario N2E 1W8
Phone
Hours
Mon–Fri 9 AM–5 PM • Sat 9 AM–1 PM
- Choosing a selection results in a full page refresh.
