Menu
Oven Temperature Wrong or Showing F3/F4 Error? Sensor W10833885 – Fix Oven Temperature Failure Fast
If your Whirlpool, KitchenAid, Maytag, or Jenn-Air range oven is running too hot, too cold, showing an F3 or F4 error code, or not heating at all, the oven temperature sensor is the most common cause. In most Whirlpool-built ranges, the temperature sensor (RTD/thermistor) monitors the oven cavity temperature and sends resistance-based signals to the control board to regulate heating. When it fails or drifts out of spec, the control board receives incorrect data — causing the oven to overheat, underheat, or shut down entirely. ⚡ Common failure point in Whirlpool, KitchenAid, Maytag, and Jenn-Air electric and gas ranges. Part W10833885 is the genuine OEM replacement that restores accurate temperature control with a direct plug-and-play fit and no modifications required.
❓ Is This the Right Part?
This is the correct fix if ALL of the following are true:
- ✔ Your range powers on and surface burners work normally
- ✔ The oven displays an F3, F4, or temperature sensor fault code
- ✔ The oven heats but runs significantly hotter or cooler than the set temperature
- ✔ The oven ignitor or bake element has been confirmed functioning
- ✔ ONLY problem is inaccurate oven temperature, error codes, or oven not heating
Not sure? Send us your model number — we'll confirm before you order.
🔧 Common Symptoms
- Oven runs too hot or too cold — food burns or is undercooked at correct settings
- F3 or F4 error code displayed on the control panel
- Oven not heating at all despite the element or ignitor functioning
- Oven temperature fluctuates wildly during a bake cycle
- Oven preheats then shuts off before reaching set temperature
- Oven cycles on and off too frequently or not frequently enough
✔ If these symptoms match, the temperature sensor is the most likely failed component in the system.
✔ In most cases, replacing the temperature sensor restores accurate oven temperature control immediately.
📦 Part Details
- Part Number: W10833885
- Type: OEM Oven Temperature Sensor / RTD Sensor / Thermistor — genuine Whirlpool factory part
- Replaces: OEM direct-fit sensor — supersedes W10586204 (no modification required)
- Brands: Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana
⚠️ Recommended While Repairing:
While the oven is open, inspect the sensor wiring harness for heat damage, fraying, or melted insulation — a damaged harness causes the same F3/F4 codes and will fail the new sensor quickly if not replaced at the same time. Replacing both together is the correct repair.
While the oven is open, inspect the sensor wiring harness for heat damage, fraying, or melted insulation — a damaged harness causes the same F3/F4 codes and will fail the new sensor quickly if not replaced at the same time. Replacing both together is the correct repair.
⚙️ Installation
Skill Level: EASY — 10–15 minutes. Disconnect power at the breaker before beginning. Open the oven door and locate the temperature sensor probe mounted at the back wall of the oven cavity — it is typically held by one or two screws. Remove the screws, pull the sensor through the oven wall, disconnect the wire harness connector, and connect the new W10833885 in its place. Route the sensor back through the wall, secure the mounting screws, restore power, and run a preheat cycle to confirm accurate temperature. Do not overtighten the mounting screws — the sensor bracket is thin and will bend.
💡 Pro Tip
Test Before You Replace:
A healthy oven temperature sensor reads approximately 1,080–1,090 ohms of resistance at room temperature (70°F/21°C). Use a multimeter set to ohms and probe the sensor connector pins. If the reading is open (OL), shorted (0Ω), or significantly outside this range, the sensor has failed and needs replacement. This 30-second test confirms the sensor — not the control board — is the root cause before you spend money on parts.
A healthy oven temperature sensor reads approximately 1,080–1,090 ohms of resistance at room temperature (70°F/21°C). Use a multimeter set to ohms and probe the sensor connector pins. If the reading is open (OL), shorted (0Ω), or significantly outside this range, the sensor has failed and needs replacement. This 30-second test confirms the sensor — not the control board — is the root cause before you spend money on parts.
🔗 Model Repair Hubs
Find part lists, diagrams, and repair guides for your specific range model: WFE540H0EB0, WFE540H0ES0, WFE540H0EW0, WFE745H0FE0, WFE745H0FH0, WFE745H0FS0, WFE770H0FZ0, WFE715H0EE0, WFE715H0ES0, WFG515S0EB0, WFG515S0ES0, WFG515S0JS0, WFG525S0HS0, WFG525S0HW0, WFG525S0JS0, WFG525S0JW0, WFG530S0EB0, WFG530S0ES0, WFG540H0EB0, WFG540H0ES0, WFG540H0EW0, WFG550S0HB0, WFG550S0HW0, WFG550S0HZ0, WFG745H0FE0, WFG745H0FS0, WFG770H0FZ0, WFG715H0EE0, WFG715H0ES0, WFG975H0HV1, WEE510S0FB0, WEE510S0FS0, WEE510S0FW0, WEE745H0FE0, WEE745H0FH0, WEE745H0FS0, WEE730H0DB0, WEE730H0DS0, WEE760H0DS0, WEG515S0FB0, WEG515S0FS0, WEG745H0FE0, WEG745H0FS0, WEG730H0DS0, WEC310S0FB0, WEC310S0FS0, WEC310S0FW0, WEC530H0DS0, WEC530H0DW0, MER8800FB0, MER8800FW0, MER8800FZ0, MER8700DB1, MER8700DS1, MGR8800FB0, MGR8800FW0, MGR8800FZ0, MGR8700DB2, MGR8700DS2, MGR8600DE0, MGR8600DS0, KSEG700ESS0, KSEG700EWH0, KSDB900ESS0, KSDG950ESS0, KSEB900ESS0, KSGG700ESS0, KSGB900ESS0, KFEG500ESS0, KFEG500EWH0, KFGG500ESS0, KFGG500EWH0, AGR6603SFB0, AGR6603SFS0, AGR6603SFW0, AGR6303MFB0, AGR6303MFS0, JDS1450DP0, JDS1450DS0, JES1450DS0, JES1450FS0, JGS1450DS0, JGS1450FS0
✓ Model-Specific Repair Pages
✅Compatibility & Cross Reference
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
Buy Online Pick Up In-Store
Address
101 Trillium Dr
Kitchener, Ontario N2E 1W8
Kitchener, Ontario N2E 1W8
Phone
Hours
Mon–Fri 9 AM–5 PM • Sat 9 AM–1 PM
- Choosing a selection results in a full page refresh.
