Washer Not Spinning or Agitating? Drive Motor W10890624 – Fix No-Spin Failures Fast

If your Whirlpool-platform top-load washer won’t spin, won’t agitate, or makes a loud humming noise during the cycle, the drive motor is the most common cause. In most Whirlpool, Maytag, and Amana top-load washers, the drive motor powers both the agitation and spin functions — when it fails, the drum sits still, clothes come out soaking wet, or the machine hums without moving. ⚡ Common failure point across Whirlpool-built top-load washers in the WTW, NTW, ITW, and WET series. Part W10890624 is the genuine OEM replacement that supersedes W10623547 and restores full agitation and spin performance immediately.

❓ Is This the Right Part?

This is the correct fix if ALL of the following are true:

• ✔ Washer powers on and fills with water normally
• ✔ Lid switch and door latch are confirmed working
• ✔ Drive belt (if applicable) is intact and not broken
• ✔ Control board advances the cycle timer
• ✔ ONLY problem is drum not spinning, not agitating, or motor humming without movement

Not sure? Send us your model number — we’ll confirm before you order.

🔧 Common Symptoms

• Washer won’t spin — clothes come out soaking wet — most common complaint
• Washer won’t agitate — drum sits still during the wash cycle
• Loud humming or buzzing during spin or agitate with no drum movement
• Washer starts then stops mid-cycle at the spin or agitate stage
• Motor runs intermittently — works sometimes, fails other times
• Burning smell from the motor area during operation

✔ If these symptoms match, the drive motor is the most likely failed component in the system.

✔ In most cases, replacing this drive motor restores full spin and agitation immediately.

📦 Part Details

• Part Number: W10890624
• Type: Washer Drive Motor Assembly
• Replaces: OEM direct-fit drive motor — supersedes W10623547 (no modification required)
• Brands: Whirlpool, Maytag, Amana, Inglis, Crosley
• OEM Option: Genuine Whirlpool factory part — guaranteed fit and full OEM lifespan
• Used Option: Tested pull — inspected for function. Ideal for older units where OEM cost isn’t justified.

⚙️ Installation

Skill Level: MODERATE — 30–45 minutes. Disconnect power at the breaker before starting. The drive motor is accessed by removing the cabinet panels and disconnecting the wiring harness and mounting hardware from the pump and motor assembly. Slide the motor off the pump, transfer the pump to the new motor, and reinstall — ensure the motor coupling seats fully before reassembling. Restore power and run a spin cycle to confirm operation.

💡 Pro Tip

Model hub pages: 11020232710, 11020232711, 11022532511, 11022532512, 7MWET4027HW0, 7MWGT4027HW0, 7MWGT4027HW1, CAW35114GW0, CAW35114GW1, ITW4871FW0, ITW4871FW1, ITW4871FW2, NTW4516FW0, NTW4516FW1, NTW4516FW2, NTW4516FW3, NTW4665GW0, RTW4516FW0, RTW4516FW1, VAW3584GW0, VAW3584GW1, WET4027HW0, WET4027HW1, WETLV27HW0, WETLV27HW1, WETLV27HW2, WGT4027HW0, WGTLV27HW0, WGTLV27HW1, WTW4616FW0, WTW4616FW1, WTW4816FW1, WTW4816FW2, WTW5000DW3, YWET4027HW0, YWET4027HW1

✓ Model-Specific Repair Pages