Dishwasher Won’t Start or Panel Is Dead? Control Board W11672229 – Fix Cycle Errors Fast
If your Jenn-Air dishwasher won’t start, stops mid-cycle, or the control panel is completely unresponsive, a failed electronic control board is the most likely cause. In most Jenn-Air dishwashers, the main control board governs every wash cycle, controls the pump, heater, and door latch, and communicates with the user interface panel. When it fails, the dishwasher may refuse to start, display persistent fault codes, or go entirely dead. ⚡ The primary logic board is the first suspect when all other components test good. Part W11672229 is the genuine OEM replacement that restores full electronic control, directly superseding W11591729 with no modification required.
❓ Is This the Right Part?
This is the correct fix if ALL of the following are true:
- ✔ Dishwasher has power — breaker is on and outlet is confirmed live
- ✔ Door latch and latch switch have been tested and are functioning correctly
- ✔ Thermal fuse has been tested and shows continuity (not blown)
- ✔ Control panel / UI board has been inspected and is not the source of the fault
- ✔ ONLY problem is no start, dead panel, mid-cycle shutdown, or persistent error codes that won’t clear after a hard reset
Not sure? Send us your model number — we’ll confirm before you order.
🔧 Common Symptoms
- Dishwasher won’t start or respond to any button input — most common customer complaint
- Control panel completely dead — no lights, no display, no beeps
- Dishwasher stops mid-cycle and won’t resume
- Persistent error or fault codes that won’t clear after unplugging and resetting
- Wash cycle runs but gets stuck on one phase and never advances
- Dishwasher starts randomly or behaves erratically between cycles
✔ If these symptoms match, the electronic control board is the most likely failed component in the system.
✔ In most cases, replacing the control board restores normal operation immediately.
📦 Part Details
- Part Number: W11672229
- Type: Dishwasher electronic control board (main logic board) — governs all wash cycles, pump, heater, door latch, and UI communication
- Replaces: OEM direct-fit control board — supersedes W11591729 (no modification required)
- Brands: Jenn-Air
A failed door latch switch or a blown thermal fuse can mimic a dead control board exactly — the dishwasher won’t start and shows no response. Both are far cheaper than a control board and take minutes to test with a multimeter. Confirm power is reaching the board and both components test good before committing to a board replacement.
⚙️ Installation
Skill Level: MODERATE — 30 to 60 minutes. Disconnect power at the breaker before beginning — this board carries line voltage and must not be handled live. The control board is located behind the door panel or inside the control console; remove the door panel screws and carefully disconnect all wire harness connectors (photograph each connector before removing). The board is static-sensitive — avoid touching circuit traces and work on a non-static surface. Release the board from its mounting clips or screws, install the new W11672229 in the same position, reconnect all harnesses firmly, reassemble the door panel, restore power, and run a full test cycle to confirm operation.
💡 Pro Tip
Electronic control boards are typically final sale once installed. Before ordering, confirm power is reaching the board with a multimeter, test the door latch switch for continuity, and check the thermal fuse. If the board receives power and all inputs test good but the dishwasher still won’t respond, the board is the correct diagnosis. Skipping this step is the most common reason for a costly misdiagnosis on high-value control boards.
🔗 Model Repair Pages
✓ Model-Specific Repair Pages
✅Compatibility & Cross Reference
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
Buy Online Pick Up In-Store
Kitchener, Ontario N2E 1W8
- Choosing a selection results in a full page refresh.
