Oven Not Heating Evenly? GE Tangential Blower WS01F03814 – Fix Convection Failure Fast

If your GE Monogram or GE Profile dual-fuel or gas range is failing to heat evenly, running hot spots, or the convection fan isn't circulating air properly, the tangential blower is the most common cause. In most ZDP-series GE Monogram ranges, this is caused by a failed tangential blower motor assembly. When it fails, the oven loses proper convection airflow — resulting in uneven baking, longer cook times, and in some cases the oven appearing to not heat at all. ⚡ Common failure point in GE-built professional dual-fuel and gas ranges. Part WS01F03814 is the genuine OEM replacement that restores full convection airflow and even heat distribution to your oven cavity.

❓ Is This the Right Part?

This is the correct fix if ALL of the following are true:

• ✔ QUALIFIER 1 — Appliance powers on and ignites normally
• ✔ QUALIFIER 2 — Bake and broil elements/burners function but heat is uneven
• ✔ QUALIFIER 3 — Gas supply or electrical supply confirmed OK
• ✔ ONLY problem is poor convection, hot spots, or fan not spinning in oven cavity

Not sure? Send us your model number — we'll confirm before you order.

🔧 Common Symptoms

• Oven not heating evenly — hot spots or cold zones during baking
• Convection fan not spinning or making unusual noise
• Longer-than-normal preheat times
• Oven appears to heat but food is undercooked or unevenly browned

✔ If these symptoms match, this is the most likely failed component in the system.

✔ In most cases, replacing this tangential blower restores normal convection operation immediately.

📦 Part Details

• Part Number: WS01F03814
• Type: Oven Tangential Blower Motor Assembly
• Replaces: 1536491, AH2364751, AH9864246, AP4436213, AP6035679, EA2364751, EA9864246, EAP2364751, EAP9864246, PS2364751, PS9864246, WB26K10010
• Brands: GE, GE Monogram, GE Profile

⚙️ Installation

Skill Level: MODERATE — 45–75 minutes. Disconnect power and shut off gas before servicing. Remove the oven rear panel to access the blower assembly, disconnect the wiring harness, unbolt the old unit, and install the new blower in reverse order. Verify fan spins freely before reassembling.

✓ Compatible Models

Confirmed compatible with ZDP304LP1SS, ZDP304NP1SS, ZDP364LDP1SS, ZDP364NDP1SS, ZDP366LP1SS, ZDP366NP1SS, ZDP484LGP1SS, ZDP484NGP1SS, ZDP486LDP1SS, ZDP486NDP1SS plus 76 additional GE Monogram ZDP-series models. Contact us to verify your model number before ordering.

💡 Pro Tip

Replaces Part Numbers

1536491, AH2364751, AH9864246, AP4436213, AP6035679, EA2364751, EA9864246, EAP2364751, EAP9864246, PS2364751, PS9864246, WB26K10010

Fits Models

ZDP304LP1SS, ZDP304LP2SS, ZDP304LP3SS, ZDP304LP4SS, ZDP304LP5SS, ZDP304LP6SS, ZDP304LP7SS, ZDP304NP1SS, ZDP304NP2SS, ZDP304NP3SS, ZDP304NP4SS, ZDP304NP5SS, ZDP304NP6SS, ZDP304NP7SS, ZDP364LDP1SS, ZDP364LDP2SS, ZDP364LDP3SS, ZDP364LDP4SS, ZDP364LDP5SS, ZDP364LDP6SS, ZDP364LDP7SS, ZDP364LRP1SS, ZDP364LRP2SS, ZDP364LRP3SS, ZDP364LRP4SS, ZDP364LRP5SS, ZDP364LRP6SS, ZDP364NDP1SS, ZDP364NDP2SS, ZDP364NDP3SS, ZDP364NDP4SS, ZDP364NDP5SS, ZDP364NDP6SS, ZDP364NDP7SS, ZDP364NRP1SS, ZDP364NRP2SS, ZDP364NRP3SS, ZDP364NRP4SS, ZDP364NRP5SS, ZDP364NRP6SS, ZDP366LP1SS, ZDP366LP2SS, ZDP366LP3SS, ZDP366LP4SS, ZDP366LP5SS, ZDP366LP6SS, ZDP366NP1SS, ZDP366NP2SS, ZDP366NP3SS, ZDP366NP4SS, ZDP366NP5SS, ZDP366NP6SS, ZDP484LGP1SS, ZDP484LGP2SS, ZDP484LGP3SS, ZDP484LGP4SS, ZDP484LGP5SS, ZDP484LGP6SS, ZDP484LGP7SS, ZDP484NGP1SS, ZDP484NGP2SS, ZDP484NGP3SS, ZDP484NGP4SS, ZDP484NGP5SS, ZDP484NGP6SS, ZDP484NGP7SS, ZDP486LDP1SS, ZDP486LDP2SS, ZDP486LDP3SS, ZDP486LDP4SS, ZDP486LDP5SS, ZDP486LDP6SS, ZDP486LDP7SS, ZDP486LRP1SS, ZDP486LRP2SS, ZDP486LRP3SS, ZDP486LRP4SS, ZDP486LRP5SS, ZDP486LRP6SS, ZDP486NDP1SS, ZDP486NDP2SS, ZDP486NDP3SS, ZDP486NDP4SS, ZDP486NDP5SS, ZDP486NDP6SS, ZDP486NDP7SS, ZDP486NRP1SS, ZDP486NRP2SS, ZDP486NRP3SS, ZDP486NRP4SS, ZDP486NRP5SS, ZDP486NRP6SS

✓ Model-Specific Repair Pages