Dryer Making Loud Squealing or Thumping Noise? Bearing Slide WW02A00250 – Fix Drum Noise Fast
Worn drum bearing slides are the most common cause of loud squealing, scraping, or thumping noises in GE and Hotpoint dryers. In most GE-built dryers, the bearing slides (also called drum glides or drum pads) support the front edge of the drum as it rotates. When they wear down, the metal drum rides directly on the cabinet, creating grinding or squealing sounds and accelerating damage to the drum and front panel. ⚡ Common wear item in GE-built dryers — typically all slides fail together. Part WW02A00250 is the genuine OEM replacement that eliminates drum noise and restores smooth, quiet operation immediately — no modification required.
❓ Is This the Right Part?
This is the correct fix if ALL of the following are true:
- ✔ Dryer powers on and heats normally
- ✔ Drum belt is intact and drum turns when started
- ✔ Idler pulley and drum rollers spin freely without roughness
- ✔ Noise is coming from the front of the drum, not the rear
- ✔ ONLY problem is squealing, scraping, or thumping noise during tumbling
Not sure? Send us your model number — we'll confirm before you order.
🔧 Common Symptoms
- Loud squealing or squeaking noise when dryer is running — most common customer complaint
- Scraping or grinding sound during drum rotation
- Thumping or rumbling noise that worsens over time
- Noise is loudest at the start of a cycle and may quiet down briefly
- Visible wear marks or grooves on the front drum lip
- Dryer vibrates more than usual during operation
✔ If these symptoms match, this is the most likely failed component in the system.
✔ In most cases, replacing the bearing slides restores quiet, smooth drum operation immediately.
📦 Part Details
- Part Number: WW02A00250
- Type: Dryer Drum Bearing Slide — front drum support glide/pad
- Replaces: OEM direct-fit slides — supersedes WW03A00016, WE3M52, 278B1139P003 (no modification required)
- Brands: GE, Hotpoint, Profile
Drum bearing slides wear at the same rate — if one is worn, the others are too. Replacing only one slide leaves uneven support on the drum and the noise will return quickly. Order a full set and replace all slides in a single teardown to avoid a repeat repair.
⚙️ Installation Notes
Skill Level: MODERATE — 30–45 minutes. Disconnect power before beginning. Access the drum slides by removing the front panel of the dryer — this typically requires removing the top panel first, then the front panel to expose the drum front bearing. Peel or unclip the old slides from the front bulkhead, clean the mounting surface, and press the new slides firmly into position. Reassemble and run a short cycle to confirm quiet operation.
✓ Compatible Models
Confirmed compatible with GTV21GSSJ0WW, GTV21GSSJ1WW, GTX18ESSJ0WW, GTX18GSSJ0WW, GTX18GSSJ1WW, GTX18PSSJ0WW, GTX22EASK0WW, GTX33EASK0WW, GTX42EASJ0WW, GTX42GASJ0WW, GTX60EBSJ0WS, GTX65EBSJ0WS, GTX65GBSJ0WS, GTX65GBSJ1WS, GUD24ESSJ0WW, GUD27ESSJ0WW, HTDP120ED4WW, HTDP120GD4WW, HTDX100ED3WW, HTDX100GD3WW, HTDX100EM5WW, HTDX100GM5WW, HTDX100PD5WW, PFDN440EL1WW, PFDN445EL1MG, PFDS451EL1WW, PFDS455EL1MG, plus additional GE and Hotpoint models. Contact us to verify your model number before ordering.
💡 Pro Tip
With the front panel off, you have full access to the drum belt and idler pulley — two other common noise sources in GE dryers. Spin the idler pulley by hand and check for roughness or wobble. If the belt shows cracking or glazing, replace it at the same time. Doing all three in one teardown saves a second disassembly call later.
✅Compatibility & Cross Reference
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
Buy Online Pick Up In-Store
Kitchener, Ontario N2E 1W8
- Choosing a selection results in a full page refresh.
