Frigidaire Dryer Upper Drum Felt and Glide Kit 5303937139

Is This the Right Part?

✅ Cross Reference Information

Common Symptoms

• Dryer makes squealing or squeaking noises (especially during drum rotation)
• Dryer makes grinding noises
• Drum rotates roughly or unevenly
• Visible wear marks or grooves on felt or glide surfaces
• Air leaking from front of dryer during operation
• Dryer takes longer to dry clothes (due to air leaks reducing heating efficiency)
• Drum wobbles or shifts during rotation
• Dryer vibrates excessively during operation
• Drum rubs against front panel
• Drum rotation is not smooth
• Loud thumping or banging noises during drum rotation
• Drum difficult to rotate by hand
• Front panel shows wear marks from drum contact
• Dryer louder than normal during operation
• Reduced heating efficiency

Check Before Replacing

• Inspect the upper front felt for wear, separation, or missing nylon glides.
• Check for visible clothing marks or snagging associated with the front drum opening.
• Listen for scraping or squealing while the drum rotates.
• Verify the complete dryer model number before ordering because felt and glide dimensions may vary.

Pro Tip

Part Details

Installation Notes

• Unplug the dryer
• from the electrical outlet to ensure complete power disconnection.
• Close the gas supply valve
• (if applicable for gas dryers) to prevent gas discharge during disassembly.
• Empty the dryer
• of any clothes or items inside.
• Remove the lint filter
• from the lint trap and set it aside.
• Remove the top panel
• of the dryer by unscrewing the fasteners along the back edge (typically 2-4 screws) and lifting the panel up and away from the cabinet.
• Take multiple photos
• of the drum felt and glide location, mounting position, and the front panel area before disassembly. Document the felt position, glide position, orientation, and any visible components from multiple angles. This is critical for proper reassembly.
• Remove the front panel
• of the dryer by locating and removing the fasteners (typically 4-6 screws along the sides or bottom). Disconnect any wire harness connectors attached to the door switch. Carefully pull the front panel away and set it aside.
• Support the drum
• as you remove the front panel to prevent it from falling forward.
• Locate the drum felt
• on the front rim of the drum. It's typically a continuous felt strip that wraps around the entire front rim.
• Locate the drum glides
• on the front panel. They're typically positioned on the left and right sides of the panel where the drum rim contacts the panel.
• Take a photo of the old felt and glides
• and their exact position before removal.
• Remove the drum belt
• from the motor pulley and idler pulley by carefully pulling the belt off. Note the belt routing for reassembly.
• Carefully lift the drum
• out of the dryer cabinet and set it aside in a safe location. The drum is heavy—use proper lifting techniques or get assistance.
• Inspect the drum rim
• where the felt and glides contact. Look for wear marks, grooves, or damage. A damaged drum rim may need resurfacing or the drum may need replacement.
• Remove the old drum felt
• from the drum rim by carefully peeling it off. The felt may be secured with adhesive or clips. Use a flathead screwdriver or putty knife to carefully pry adhesive-mounted felt.
• Clean the drum rim
• thoroughly with a clean cloth. Remove any old adhesive, lint, or debris. The drum rim surface must be clean and smooth for proper felt adhesion.
• Remove the old drum glides
• from the front panel by unscrewing the mounting screws (if present) or carefully prying them off if they're adhesive-mounted.
• Clean the glide mounting area
• on the front panel thoroughly with a clean cloth. Remove any old adhesive, lint, or debris. The mounting surface must be clean and smooth for proper glide adhesion.
• Inspect the front panel
• for damage, cracks, or corrosion. Repair or replace the front panel if damage is present.
• Unpack the new 5303937139 drum felt and glide kit
• from its packaging. Handle carefully to avoid damaging the felt, glides, or components.
• Verify all components are included
• in the kit: drum felt strip, glide pieces (typically 2 or 4 pieces), mounting screws (if applicable), and adhesive strips (if applicable).
• Compare the new felt and glides to the old ones
• to verify the size, shape, and configuration match. Ensure you have the correct replacement kit.
• Inspect the new felt and glides
• for any damage or defects before installation.
• Install the new drum felt
• on the drum rim. Remove the protective backing from the adhesive strip on the felt. Starting at one end, carefully position the felt on the drum rim and press firmly as you work around the entire rim. Ensure the felt is centered on the rim and not twisted or wrinkled.
• Overlap the felt ends
• slightly (typically 1/4 to 1/2 inch) where they meet. Trim excess felt with scissors if necessary.
• Press the felt firmly
• around the entire drum rim for 30-60 seconds to ensure proper adhesion.
• Position the new glides
• on the front panel in the exact location as the old glides. Use your photos as a reference.
• For screw-mounted glides:
• Align the glide mounting holes with the front panel holes and secure with the mounting screws. Tighten firmly but not over-tightening (which can crack the glides or strip threads).
• For adhesive-mounted glides:
• Remove the protective backing from the adhesive strip on the glide. Carefully position the glide on the front panel in the exact location as the old glide. Press firmly for 30-60 seconds to ensure proper adhesion.
• Verify the glides are properly positioned
• by comparing them to your photos. The glides should be at the same position and orientation as the old glides.
• Verify the glides are level and aligned
• with each other. Misaligned glides can cause uneven drum rotation and premature wear.
• Allow adhesive-mounted components to cure
• for at least 30 minutes before reinstalling the drum. This ensures proper adhesion.
• Reinstall the drum
• by carefully lowering it into the dryer cabinet and aligning it with the rear drum support and front glides.
• Verify the drum rim with felt rests properly
• on the front glides. The drum should be centered and level on the glides.
• Reinstall the drum belt
• by routing it around the drum, motor pulley, and idler pulley exactly as shown in your photos. The belt should be centered on all pulleys and not twisted.
• Verify belt tension
• by pressing on the belt midway between pulleys. The belt should deflect approximately 1/2 inch (12-15mm) under moderate pressure.
• Manually rotate the drum
• by hand to verify it rotates smoothly without binding or resistance. The drum should spin freely and quietly.
• Verify the drum does not wobble
• or shift during rotation. The drum should rotate smoothly and stay centered on the glides.
• Verify the felt creates a proper seal
• by checking that there are no visible gaps between the felt and the front panel as the drum rotates.
• Reinstall the front panel
• by aligning it with the dryer and securing all fasteners. Reconnect any wire harness connectors to the door switch.
• Reinstall the top panel
• by aligning it with the dryer and securing all fasteners along the back edge.
• Reinstall the lint filter
• into the lint trap.
• Restore the gas supply
• (if applicable) by opening the gas supply valve.
• Plug the dryer back in
• and restore power.
• Run a test cycle
• (without clothes) on a short drying cycle to verify proper felt and glide operation.
• Verify the drum rotates smoothly
• during the test cycle without unusual noises or vibrations.
• Listen for squealing, squeaking, or grinding noises
• during the entire cycle. The drum should rotate quietly with only normal mechanical sounds.
• Monitor for air leaks
• by feeling around the front panel during operation. No air should be escaping from the front of the dryer.
• Monitor for unusual vibrations
• throughout the test cycle. The dryer should operate smoothly without excessive shaking.
• If squealing or squeaking noises occur
• , the felt or glides may not be properly positioned or the drum rim may be damaged. Stop the cycle and verify felt and glide position and drum rim condition.
• If grinding noises occur
• , the drum may be rubbing against the front panel or the glides may be misaligned. Stop the cycle and verify glide alignment.
• If air leaks are detected
• , the felt may not be properly sealed or may have gaps. Stop the cycle and verify felt installation and sealing.
• If the drum wobbles or shifts
• , the glides may be misaligned or not level. Stop the cycle and verify glide position and alignment.
• Run a full drying cycle
• with a typical load of clothes to confirm the repair is complete and the dryer operates normally.
• Monitor drying efficiency
• over the next few cycles. Clothes should dry in normal time without extended drying cycles.
• Monitor the dryer for 24-48 hours
• of normal use to ensure it operates properly without unusual noises, vibrations, or performance issues.
• Safety Notes:
• Always unplug the dryer before working on it. Close the gas supply valve (if applicable) to prevent accidental gas discharge. The drum is heavy—use proper lifting techniques or get assistance. Never operate the dryer without the drum felt and glides installed—this can damage the drum rim, front panel, and reduce drying efficiency. Ensure the felt and glides are properly positioned and secured before operating the dryer. Allow adhesive-mounted components to cure fully before reinstalling the drum.

Verified Compatible Models

41749012890, 41749022890, 41759012890, 41759022890, CREF342AS0, CRER442AS0, CRGF342AS0, CRGR442AS0, EDE16NS0, EDG16NS0, ELXG42RED1, FD955EAW0, FDE216RES1, FDE216RES2, FDE336CFS2

Fitment reminder: Match the complete appliance model number, including suffix or revision where applicable, before ordering.