Menu
Dryer Squealing or Grinding? Rear Bearing Kit 5303281153 – Fix Drum Noise Fast
If your Frigidaire dryer is squealing, grinding, or leaving black marks on clothes, the rear drum bearing is the most likely cause. In Frigidaire and Electrolux-built dryers, the rear bearing supports the drum through thousands of rotations under load — when it wears out, friction heat builds immediately, causing squealing, grinding, and eventually scoring the drum shaft or burning out the drive motor. ⚡ Common failure point in Frigidaire-built dryers after years of thermal cycling. Part 5303281153 is the OEM rear bearing kit that restores smooth, quiet drum rotation and eliminates all bearing-related noise immediately.
❓ Is This the Right Part?
This is the correct fix if ALL of the following are true:
- ✔ Dryer powers on and heats normally
- ✔ Drive belt is intact and not slipping
- ✔ Front drum glides and support rollers have been checked
- ✔ Drum feels rough, catchy, or wobbles when rotated by hand
- ✔ ONLY problem is squealing, grinding, or thumping noise during tumbling
Not sure? Send us your model number — we'll confirm before you order.
🔧 Common Symptoms
- Rhythmic squeaking or squealing that gets louder with each cycle — most common complaint
- Grinding or metal-on-metal scraping sound during tumbling
- Thumping or rumbling that worsens with heavier loads
- Black marks, streaks, or metal shavings appearing on clothes
- Burning smell during operation from friction heat
- Drum wobbles or sits off-centre when pushed by hand
- Drum stalls or stops mid-cycle (bearing seized)
- Drive belt breaking repeatedly from excessive drum drag
- Dryer taking much longer than normal to dry a load
✔ If these symptoms match, this is the most likely failed component in the drum support system.
✔ In most cases, replacing the rear bearing kit restores quiet, smooth drum rotation immediately.
📦 Part Details
- Part Number: 5303281153
- Type: Dryer Rear Drum Bearing Kit — includes bearing and retainer
- Replaces: OEM direct-fit rear bearing kit — supersedes 31581400, 3281153, 724C138A02, 902088, Q000142850, WQ142850, 131378400, 131777700, 137086600, 137088600, 137088620, 137088630 (no modification required)
- Brands: Frigidaire, Electrolux, Kenmore, Gibson, Kelvinator, Tappan, White-Westinghouse
- Options: OEM and XPart (premium aftermarket) variants available — select above. XPart parts are not affiliated with or endorsed by Frigidaire or Electrolux.
⚠️ Recommended While Repairing:
Removing the drum is the hardest part of this job — while it’s out, inspect the front drum glides, drum support rollers, and idler pulley, which all wear at the same rate and cause identical noise symptoms. Replacing all wear components in one visit eliminates every noise source and prevents a repeat teardown in 6–12 months.
Removing the drum is the hardest part of this job — while it’s out, inspect the front drum glides, drum support rollers, and idler pulley, which all wear at the same rate and cause identical noise symptoms. Replacing all wear components in one visit eliminates every noise source and prevents a repeat teardown in 6–12 months.
⚙️ Installation
Skill Level: MODERATE to ADVANCED — 60 to 90 minutes. Unplug the dryer before beginning. Remove the top panel, front panel, and drum to access the rear bearing on the back bulkhead. Photograph the drive belt routing before removing the drum — correct routing is critical for reassembly. Apply a thin layer of high-temperature bearing grease (rated 400°F+) to the new bearing surface and drum shaft before installing. Spin the drum by hand after reassembly to confirm smooth, quiet rotation before closing the cabinet. Run an empty cycle first before loading clothes.
✓ Compatible Models
Confirmed compatible with hundreds of Frigidaire, Electrolux, Kenmore, Gibson, Kelvinator, Tappan, and White-Westinghouse dryer models including AEQ6000CES0, AEQ7000CES0, AEQ8000CFE0, AGQ8000FE0, CLCE500FW0, CLCG500FW0, CDE4000FW0, CDG4000FW0, and many more. Contact us to verify your model number before ordering.
💡 Pro Tip — Replace All Wear Components While the Drum Is Out:
The rear bearing, front drum glides, drum support rollers, and idler pulley all wear together — if one has failed, the others are close behind. Replacing all four in a single visit costs an extra 20 minutes and eliminates every noise source in the dryer. Doing them separately means a full teardown again in 6–12 months. Ask us about the complete wear kit for your model.
The rear bearing, front drum glides, drum support rollers, and idler pulley all wear together — if one has failed, the others are close behind. Replacing all four in a single visit costs an extra 20 minutes and eliminates every noise source in the dryer. Doing them separately means a full teardown again in 6–12 months. Ask us about the complete wear kit for your model.
✅Compatibility & Cross Reference
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
Buy Online Pick Up In-Store
Address
101 Trillium Dr
Kitchener, Ontario N2E 1W8
Kitchener, Ontario N2E 1W8
Phone
Hours
Mon–Fri 9 AM–5 PM • Sat 9 AM–1 PM
- Choosing a selection results in a full page refresh.
