Frigidaire EI24ID30QB3B Dishwasher Not Draining: Checks, Drain Hose and Pump Parts

Does your Frigidaire EI24ID30QB3B dishwasher leave water behind? Start by determining whether there is only a small amount of water in the filter or sump area or a deeper pool across the bottom of the tub. Then confirm that the cycle finished and use the dishwasher’s available Cancel/Drain function, if provided. If substantial water remains, check only the accessible drain path first.

Several components or conditions can create a “not draining” symptom. The filter or glass-trap area may need cleaning, the drain hose may be kinked or restricted, or the dishwasher drain pump may not be moving water effectively. Water can also return from the sink or garbage-disposal connection rather than failing to leave the dishwasher in the first place. These possibilities can look similar, so the symptom alone does not prove that one specific part is defective.

How much water is left in the Frigidaire EI24ID30QB3B dishwasher?

A shallow amount confined to the filter or sump area is different from a deep pool covering the bottom of the dishwasher. Note the amount and condition of the water: clean, cloudy, dirty, or soapy. Also note whether the water remains immediately after a completed cycle or appears later after the sink or garbage disposal is used.

If the dishwasher leaves substantial water after the cycle, continue with the checks below. Do not reach into standing water while the appliance is energized. Before inspecting or removing any component, switch off power to the dishwasher using the appropriate household disconnect or circuit breaker, and follow safe appliance-service practices. If you are not comfortable working around water or electrical connections, contact a qualified appliance service professional.

What safe checks can you make before replacing a part?

• Check the cycle status: Confirm the cycle completed rather than stopping partway through. If the controls provide a Cancel/Drain function, try it according to the appliance controls.
• Inspect the accessible filter or glass-trap area: Remove visible food debris or buildup using the cleaning method appropriate for the appliance. Avoid forcing parts or using tools where they could damage the filter area.
• Inspect the drain hose: Look for a visible kink, crushing, blockage, or low section that could restrict flow. The hose should not be pinched behind the dishwasher or cabinetry.
• Check the sink or garbage-disposal connection: If the Frigidaire dishwasher is connected to a disposal, verify that the sink and disposal drain normally. A restriction at that connection can prevent dishwasher water from leaving.
• Check the countertop air gap, if installed: An air gap can collect debris and restrict the drain path. Inspect it only as an accessible check and do not disassemble anything you cannot safely identify.

Pay attention to sound when Cancel/Drain is selected. A humming or drain-pump sound, no sound, intermittent operation, and slow or partial draining can point to different areas of the drain system. These observations are useful for diagnosis, but they do not by themselves confirm whether the hose or pump needs replacement.

Could the drain hose be causing the Frigidaire dishwasher to leave water behind?

Yes. A kinked, crushed, blocked, or otherwise restricted hose can limit the dishwasher’s ability to discharge water. If the accessible hose inspection shows damage or restriction, the verified fitment option for the Frigidaire EI24ID30QB3B dishwasher is the Drain Hose, part number 807032601.

Review the hose routing and connections before ordering. Replace a hose only after confirming that the model label matches Frigidaire EI24ID30QB3B and that the part number on the listing matches 807032601. A hose replacement may not resolve the symptom if the actual restriction is at the filter, sink connection, air gap, or drain pump.

Shop Frigidaire Dishwasher Drain Hose 807032601

Could the dishwasher drain pump be responsible?

Yes. The drain pump is another possible cause when water remains after accessible restrictions have been checked. Signs such as a humming sound without effective draining, intermittent draining, or a cycle that leaves substantial water behind may warrant further pump diagnosis. However, a sound or symptom is not enough to guarantee that the pump has failed.

The verified fitment option for this model is the Dishwasher drain pump, part number A00044305. Before ordering, confirm that the appliance identification label reads Frigidaire EI24ID30QB3B and compare the required part number with A00044305. Disconnect power before any service work, and use qualified service if testing or pump replacement requires access beyond basic checks.

Shop Frigidaire Dishwasher Drain Pump A00044305

Which Frigidaire EI24ID30QB3B parts are available for this symptom?

The exact model hub for this issue includes two verified buyable products:

• Drain Hose 807032601 — a possible fit when the drain hose is visibly damaged, kinked, or restricted.
• Dishwasher drain pump A00044305 — a possible fit when the drain pump requires diagnosis or replacement.

These are not interchangeable diagnoses. A dishwasher that is not draining can involve more than one condition, and replacing a component without checking the complete drain path may leave the original symptom unchanged. Use the checks above to narrow the issue, then consult qualified appliance service when electrical testing, internal access, or uncertain diagnosis is involved.

For the complete model-specific selection, visit the Frigidaire EI24ID30QB3B dishwasher parts hub. Before purchasing, confirm the full model label on the appliance and verify the part number: 807032601 for the Drain Hose or A00044305 for the Dishwasher drain pump.

What should you confirm before ordering a part?

Confirm all of the following:

• The brand is Frigidaire.
• The appliance is a Dishwasher.
• The complete model is EI24ID30QB3B.
• The symptom is excess water remaining after a completed cycle, slow draining, or failure to drain.
• The selected part number matches the listing: 807032601 or A00044305.

Frigidaire EI24ID30QB3B dishwasher not draining FAQ

Is a small amount of water always a failure?

Not necessarily. Distinguish a small amount confined to the filter or sump area from substantial standing water across the tub. If you are unsure, document when the water appears and whether it increases after the sink or disposal is used.

Why does the dishwasher hum but still leave water behind?

Humming may indicate that the drain pump is being activated, but it does not confirm pump failure. Check the accessible filter, hose, sink or disposal connection, and air gap if installed before seeking further diagnosis.

Should I replace the hose or drain pump first?

There is no safe universal answer based only on the symptom. Inspect the drain path and compare your findings with the relevant verified part. If the cause remains uncertain, use qualified appliance service rather than replacing parts by guesswork.

Where can I find the exact parts for this dishwasher?

Use the Frigidaire EI24ID30QB3B dishwasher parts hub, and confirm the model label and part number before ordering.