OEM & Premium XPart Options Available
Samsung Dryer Drum Roller DC97-16782A – OEM & XPart Options (Replaces DC97-07523A, DC97-07523B)
Part# DC97-16782A
Replaces DC97-07523A
Fits Samsung
Rear Drum Roller
Samsung Dryer Squeaking, Thumping, or Rumbling During Spin? Drum Roller DC97-16782A – Fix Drum Noise Fast
A worn drum roller is the most common cause of squeaking, thumping, and rumbling noise in Samsung dryers — and it’s one of the most straightforward DIY repairs on the platform. In most Samsung front-load dryers, the rear drum roller supports the weight of the drum at the back of the cabinet — when the roller surface wears flat, the bearing seizes, or the axle develops play from thousands of cycles, the drum produces a rhythmic thumping or high-pitched squeal that worsens progressively until the roller fails completely. ⚡ Common failure point in Samsung dryers after high cycle counts, especially on models manufactured from 2014 onward. Part DC97-16782A is the current OEM drum roller that supersedes DC97-07523A and DC97-07523B and restores quiet, smooth drum rotation with no modifications required.
❓ Is This the Right Part?
This is the correct fix if ALL of the following are true:
- ✔ Your dryer has confirmed power and the motor runs — the drum attempts to spin during a cycle
- ✔ The drive belt has been inspected and is intact — the drum is turning, not stationary
- ✔ The idler pulley has been inspected and is not the sole source of the noise
- ✔ The drum roller feels rough, has flat spots, or wobbles when rotated by hand with the belt removed
- ✔ ONLY problem is squeaking, thumping, rumbling, or grinding noise during drum rotation
Not sure? Send us your model number — we'll confirm before you order.
🔧 Common Symptoms
- Squeaking or squealing noise during drum rotation — most common worn bearing symptom
- Rhythmic thumping or rumbling that speeds up and slows with the drum — flat-spotted roller surface
- Grinding noise from the rear of the dryer cabinet during tumbling
- Drum feels rough or uneven when rotated by hand with power disconnected
- Noise worsens progressively over weeks and doesn’t go away after warmup
- Dryer vibrates excessively during operation from drum imbalance caused by roller wear
✔ If these symptoms match, this is the most likely failed component in the system.
✔ In most cases, replacing this drum roller restores quiet, smooth drum operation immediately.
📦 Part Details
-
Part Number: DC97-16782A (current OEM number, supersedes DC97-07523A and DC97-07523B)
-
Type: Dryer Rear Drum Roller – supports the weight of the dryer drum at the rear of the cabinet; includes axle shaft; runs continuously with the drum through every cycle
-
Replaces: OEM direct-fit drum roller — supersedes DC97-07523A, DC97-07523B, WE01X32497 (no modification required)
-
Brands: Samsung
-
Available As:
-
OEM (DC97-16782A): Genuine Samsung factory roller — exact original specification
-
XPart – Updated Bearing (DE16782E): Premium aftermarket roller with upgraded bearing assembly for improved durability and quieter operation — recommended for full drum support rebuilds
-
XPart – No Bearing (DE3001E): Direct-fit aftermarket roller body — ideal when the bearing is still serviceable and only the roller surface needs replacement
-
Used: Tested, certified pre-owned OEM roller
⚠️ Recommended While Repairing:
While the drum is out to replace the roller, inspect the idler pulley and drive belt — all three components wear at the same rate through the same cycle count, and a worn idler pulley bearing will produce the same squeal within weeks of the roller replacement. Replacing the idler pulley and belt in the same teardown eliminates all drum drive noise sources in one visit.
⚙️ Installation
Skill Level: MODERATE — 30–60 minutes. Disconnect power before beginning any disassembly. Remove the front panel and lift the drum out to access the rear drum roller — refer to your model’s service manual for the exact disassembly sequence as panel removal varies by model. Swap the old roller for the new DC97-16782A, apply a small amount of high-temperature grease to the roller axle if not pre-lubricated, then reassemble in reverse order. Run a short test cycle to confirm the noise is fully resolved before considering the repair complete.
✓ Compatible Models
Part DC97-16782A supersedes DC97-07523A and DC97-07523B and is confirmed compatible with DV48H7400EW/A2, DV395ETPASU/A1, DV456EWHDSU/AA, DV45H7000GP/A3, DV50K8600EW/A3, DV45H7000EP/A3, DV22K6800EW/AC, DV40J3000GW/A2, DV40J3000EW/AC, DV45K6500GW/A3, DV45K6500GV/A3, DV45K7600GW/A3, DV45K7600EW/AC, DV45K7600EW/A3, DV45K6200GZ/A3, DV45K6200GW/A3, DV48J7770GW/A2, DV48J7770GP/A2, DV48J7770EW/AC, DV48J7700GW/A2, DV52J8700GW/A2, DV52J8700GP/A2, DV50K8600EV/AC, CDV50K8600EV/A3, DV5451AEW/XA, and many additional Samsung dryer models. Contact us with your model number to confirm compatibility before ordering.
💡 Pro Tip
Replace Both Rear Rollers at the Same Time — They Wear Together:
Samsung dryers use two rear drum rollers — one on each side of the rear drum support — and both accumulate the same cycle count and wear at the same rate. If one roller has failed, the other is within weeks of the same failure. Replacing both rollers in the same teardown costs only the price of a second roller and eliminates the need to open the dryer again in the near future.