Whirlpool Dishwasher Rack Rusted, Broken, or Dishes Not Staying in Place? Lower Dishrack W10728159 – Fix Rack Failure Fast

A rusted, broken, or deformed lower dishrack is the most common cause of dishes shifting during cycles, chipped dishware, and rust stains appearing on plates and glasses in a Whirlpool dishwasher. In most Whirlpool-built dishwashers, the lower dishrack is the primary loading platform that holds plates, pots, and larger items during the wash cycle — when the vinyl rack coating wears through, the exposed wire rusts and transfers rust stains to dishware, tines break and allow dishes to tip and chip, and the rack may no longer roll smoothly on its wheels. ⚡ Common wear item in Whirlpool-platform dishwashers after years of daily loading, high-temperature wash cycles, and detergent exposure. Part W10728159 is the genuine OEM replacement lower dishrack that restores full dish loading capacity and smooth rack operation with no modifications required.

❓ Is This the Right Part?

This is the correct fix if ALL of the following are true:

• ✔ Your dishwasher runs normally — wash and rinse cycles complete without error codes
• ✔ The dishwasher tub and door are intact — the rack mounting rails are undamaged
• ✔ The rack wheels and axles have been inspected — the issue is the rack itself, not the wheel assemblies
• ✔ The spray arm below the lower rack is confirmed unblocked and rotating correctly
• ✔ ONLY problem is rusted tines, broken tines, dishes shifting or chipping, or rust stains on dishware

Not sure? Send us your model number — we'll confirm before you order.

🔧 Common Symptoms

• Rust stains appearing on plates, glasses, or the dishwasher tub — most common rack failure symptom
• Rack tines broken, bent, or missing — dishes tip over or fall during the wash cycle
• Vinyl rack coating worn through — bare wire exposed and actively rusting
• Dishes chipping from contact with broken tines or other items during the cycle
• Rack not rolling smoothly or derailing from the mounting rails
• Rack frame bent or deformed — rack no longer sits level in the dishwasher tub

✔ If these symptoms match, this is the most likely failed component in the system.

✔ In most cases, replacing this lower dishrack eliminates rust staining and restores full dish loading capacity immediately.

📦 Part Details

• Part Number: W10728159
• Type: Dishwasher Lower Dishrack – primary loading platform for plates, pots, and larger items; vinyl-coated wire rack with tines, integrated wheel assemblies, and spray arm clearance for the lower wash arm
• Replaces: OEM direct-fit lower dishrack — supersedes 8193785, 8268635, 8268638, 8268781, 8268788, 8268805, 8268806, 8519616, 8519646, 8519667, 8519668, 8519680, 8539257, W10056271, W10078180, W10082825, W10199765, W10312777, W10315890, W10525645, W10525646, W10525651, W10889106, WP8519681, WPW10078180 (no modification required)
• Brands: Whirlpool, KitchenAid, Maytag, Amana, Jenn-Air
• Available As: OEM (genuine Whirlpool factory rack) or Used (tested, certified pre-owned)

⚙️ Installation

Skill Level: EASY — 5–10 minutes. No tools required and no power disconnect needed for this repair. Pull the old lower rack out of the dishwasher completely, transfer any wheel assemblies or axle caps from the old rack to the new W10728159 rack if they are not pre-installed, then slide the new rack onto the mounting rails and confirm it rolls smoothly to the full-open and full-closed positions. Load dishes and run a test cycle to confirm the rack stays on the rails and dishes are held securely throughout the cycle.

✓ Compatible Models

Part W10728159 supersedes 8193785, W10525645, and 24 additional part numbers and is confirmed compatible with a wide range of Whirlpool, KitchenAid, Maytag, Amana, and Jenn-Air dishwasher models. Contact us with your model number to confirm compatibility before ordering.

💡 Pro Tip