Dryer Not Heating? Heating Element W10815654 – Fix No-Heat Fast

A failed heating element is the single most common reason a Whirlpool or Maytag dryer runs but produces no heat. In most Whirlpool-built dryers, this is caused by a burned-out heating element coil that opens under thermal stress or age. When it fails, the drum tumbles normally but clothes come out cold and damp no matter how long the cycle runs. ⚡ Common failure point in Whirlpool-built dryers — especially units over 5 years old. Part W10815654 is the genuine OEM 5000W/240V replacement that restores full heat output and normal drying performance immediately.

❓ Is This the Right Part?

This is the correct fix if ALL of the following are true:

• ✔ Your dryer powers on and the drum tumbles normally
• ✔ The dryer runs a full cycle but produces little or no heat
• ✔ Your home circuit breaker and outlet voltage are confirmed OK (240V)
• ✔ The thermal fuse has been tested and is not blown
• ✔ ONLY problem is no heat — not tumbling, timer, or control issues

Not sure? Send us your model number — we’ll confirm before you order.

🔧 Common Symptoms

• Dryer runs but produces no heat — clothes come out cold and wet
• Dryer takes multiple cycles to dry a normal load
• Drum spins but no warm air from the vent
• Dryer shuts off early without completing the cycle
• No error code displayed — unit appears to run normally
• Heating element coil visibly broken or burned when inspected

✔ If these symptoms match, this is the most likely failed component in the system.

✔ In most cases, replacing this heating element restores normal drying operation immediately.

📦 Part Details

• Part Number: W10815654
• Type: Dryer Heating Element Assembly, 5000W / 240V
• Replaces: OEM direct-fit heating element assembly — supersedes 3403590, 8576779, W10724242 (no modification required)
• Brands: Whirlpool, Maytag, Amana, Kenmore

⚙️ Installation

Skill Level: MODERATE — 30–45 minutes. Unplug the dryer and disconnect from 240V power before beginning. Remove the back panel, disconnect the element leads, release the retaining bracket, slide out the old element housing, and install the new assembly in reverse order. Confirm all wire terminals are fully seated and the element coil does not contact the housing before reassembling.

💡 Pro Tip

✓ Model-Specific Repair Pages

110C60022011, 110C60102310, 110C60122510, 110C60222510, 110C60242510, 110C61292011, 110C61402311, 110C62332510, 110C66132410, YAED4370TQ0, YAED4470TQ0, YCEDS563SQ0, YEED4300TQ0, YEED4300VQ0, YEED4300VQ1, YEED4400TQ0, YEED4400WQ0, YHED4300TQ0, YHED4400TQ0, YIED4400VQ1, YIED4400VQ2, YIED4600YQ0, YIED4671DQ0, YIED4700YQ0, YIED4700YQ1, YIED4771DQ0, YMED5620TQ0, YMED5640TQ0, YMED5700TQ0, YMED5720TQ0, YMED5740TQ0, YMED5800TW0, YMED5840TW0, YMEDB755DW0, YMEDB755DW1, YMEDC300XW0, YMEDC400BW0, YMEDC415EW0, YMEDC555DW0, YMEDX6STBW0, YNED4500VQ0, YNED4600YQ0, YNED4655EW0, YNED4700YQ0, YNED4705EW0, YNED4800VQ0, YNED4800VQ1, YNED5200TQ0, YNED5500TQ0, YNED5800TQ0, YRED4300TQ0, YRED4340SQ0, YRED4340SQ2, YWED4800BQ0, YWED4800BQ1, YWED4800XQ0, YWED4800XQ1, YWED4800XQ2, YWED4850BW0, YWED4850BW1, YWED4900XW0, YWED4900XW1, YWED4900XW2, YWED4915EW0, YWED49STBW0, YWED5200VQ0, YWED5200VQ1, YWED5300VW0, YWED5700VH0, YWED5700VH1, YWED5700VW0, YWED5700VW1, YWED6200SW1, YWED6600VU0, YWED6600VW0, YWED6600WL0, YWED7300DW0