WATER LEAKING DURING DRAINING
Whirlpool Washer drain hose with bend and stay WP21001872, Fixes Water leaking during draining
Genuine Whirlpool OEM drain hose with bend and stay. It carries used water from the washer to the household drain or standpipe.
Part WP21001872Replaces 21001512, 21001513, 21001872, 31001337, 31001338, 35-2803, 35-2804, 35-3538, 35-3539Whirlpool
Guaranteed to Fit — or your money back.
Confirm your full appliance model number before ordering.
Confirm your full appliance model number before ordering.
Is This the Right Part?
Part NumberWP21001872
Replaces21001512, 21001513, 21001872, 31001337, 31001338, 35-2803, 35-2804, 35-3538, 35-3539
ManufacturerWhirlpool
Appliance TypeWasher
Part TypeWasher drain hose with bend and stay
✅ Cross Reference Information
Current Part NumberWP21001872
Replaces21001512, 21001513, 21001872, 31001337, 31001338, 35-2803, 35-2804, 35-3538, 35-3539
Common Symptoms
- Visible cracking, splitting, brittleness, abrasion, or soft spots in the hose
- Water leaking from the rear of the washer or onto the floor during drain or spin
- Slow or incomplete draining when the hose is kinked or obstructed
- Drain hose movement, noise, or poor positioning caused by incorrect routing
Check Before Replacing
- Unplug the washer before inspecting the hose or accessing the rear of the appliance.
- Visually inspect the accessible hose for cracks, splits, abrasion, flattened sections, kinks, or loose connections.
- Check whether water appears at the hose connections or along the hose during a brief drain operation, while keeping clear of moving parts and electrical components.
- Confirm that the hose is routed without sharp bends or rubbing and that its outlet is properly positioned in the standpipe or laundry tub according to the washer installation instructions.
- If the hose appears sound, also check the household drain and other drain-system components before identifying the hose as the cause.
Pro Tip
The molded bend and stay help maintain the intended outlet position; preserve that form and route the hose without kinks, rubbing, or forcing excess hose into the standpipe.
Part Details
Part NumberWP21001872
Part TypeWasher drain hose with bend and stay
ManufacturerWhirlpool
Appliance TypeWasher
Primary FunctionCarries wastewater from the washer drain pump to the household standpipe or laundry tub.
Installation Notes
- Disconnect electrical power before installation; shutting off the water supply is also recommended as a precaution.
- Access the hose connection at the washer and use care because residual water may remain in the hose.
- Transfer existing clamps or brackets only where required by the appliance design, and fully seat and secure the hose connections.
- Route the hose to avoid kinks, sharp bends, abrasion, and contact with moving or hot components.
- Secure the outlet in the standpipe or laundry tub using the washer’s installation requirements; do not force excess hose into the drain pipe.
- Run a short drain or spin test after installation and inspect the connections and hose routing for leaks.
Verified Compatible Models
AAV1000AWW, AAV2200AWW, AAV4000AWW, AAV4200AWA, AAV8005EWW, CAV2000AWW, CAV2004AWW, CAV2240LKW, CAV4000AGW, CW5000W, CW6000Q, CW6000W, CW6500Q, CW8000W, CW9505W
Fitment reminder: Match the complete appliance model number, including suffix or revision where applicable, before ordering.
Buy Online Pick Up In-Store
Address
101 Trillium Dr
Kitchener, Ontario N2E 1W8
Kitchener, Ontario N2E 1W8
Phone
Hours
Mon–Fri 9 AM–5 PM • Sat 9 AM–1 PM
