Washer Not Draining or Leaking? Whirlpool Drain Hose WPW10358149 – Restore Proper Drainage Fast
A cracked, kinked, or failed drain hose is one of the most common causes of water leaking onto the floor or a washer that won't drain at the end of a cycle. In most Whirlpool-built washers, the drain hose routes water from the tub to the standpipe or laundry sink — when it cracks, splits, or loses its seal, water backs up or pools under the machine. When it fails, you'll see standing water in the drum, water on the floor, or an error code indicating a drain fault. ⚡ Common failure point in Whirlpool, Maytag, and KitchenAid top-load and front-load washers. Part WPW10358149 is the genuine OEM replacement drain hose that restores a leak-free, fully draining washer in one repair.
❓ Is This the Right Part?
This is the correct fix if ALL of the following are true:
- ✔ QUALIFIER 1 — washer powers on and the drum spins normally
- ✔ QUALIFIER 2 — pump motor is running (you can hear it during drain cycle)
- ✔ QUALIFIER 3 — standpipe or laundry sink drain is clear and not blocked
- ✔ ONLY problem is water leaking from the hose connection or washer not fully draining
Not sure? Send us your model number — we'll confirm before you order.
🔧 Common Symptoms
- Water pooling on the floor behind or under the washer
- Washer stops mid-cycle with standing water in the drum
- Drain error code displayed (F9, E1, or similar depending on model)
- Visible cracks, splits, or kinks in the existing drain hose
- Hose has pulled away from the pump outlet or standpipe connection
✔ If these symptoms match, the drain hose is the most likely failed component.
✔ In most cases, replacing the drain hose restores full drainage and eliminates leaks immediately.
📦 Part Details
- Part Number: WPW10358149
- Type: OEM Washer Drain Hose — routes wastewater from tub to standpipe or laundry sink
- Replaces: W10358149, WPW10358149VP, 3349018, 3355497, 3357024, 3361805, 3361809, 63206, 8317940
- Brands: Whirlpool, Maytag, KitchenAid, Amana, Jenn-Air
While the washer is pulled out, inspect the water inlet hoses (hot and cold supply lines) for bulging, cracking, or mineral buildup at the fittings. These are a leading cause of catastrophic flooding and should be replaced every 5 years. A $15 hose swap now prevents thousands in water damage later.
⚙️ Installation
Skill Level: EASY — 20–30 minutes. Disconnect power and water supply before servicing. Pull the washer away from the wall, locate the drain hose at the back of the machine connected to the pump outlet, release the clamp, slide off the old hose, and slide on the new one. Secure the clamp, route the hose to the standpipe, and run a test cycle to confirm no leaks.
✓ Compatible Models
Confirmed compatible with a wide range of Whirlpool, Maytag, KitchenAid, Amana, and Jenn-Air top-load and front-load washer models. Cross-references: W10358149, WPW10358149VP, 3349018, 3355497, 3357024, 3361805, 3361809, 63206, 8317940. Contact us to verify your model number before ordering.
💡 Pro Tip
A leaking drain hose isn't always a cracked hose — sometimes the spring clamp loses tension over time and the hose slips off the pump outlet under pressure. Before ordering, check whether the hose is still firmly seated and the clamp is tight. If the hose itself is cracked, split, or hardened, WPW10358149 is your fix. Replace the clamp at the same time for a fully sealed repair.
✓ Model-Specific Repair Pages
✅Compatibility & Cross Reference
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
Buy Online Pick Up In-Store
Kitchener, Ontario N2E 1W8
- Choosing a selection results in a full page refresh.
