Menu
Washer Shaking Violently or Making Loud Banging Noises? Rear Suspension Rod WW01F01684 – Fix Excessive Vibration Fast
If your GE top load washer shakes violently, walks across the floor, or makes loud banging noises during the spin cycle, a broken rear suspension rod is the most common cause. In most GE top load washers, this is caused by a failed rear suspension rod — the spring-loaded strut that absorbs drum movement during agitation and spin. When it fails, the drum drops on one side, causing severe vibration, loud banging, and potential damage to the cabinet and tub. ⚡ Common failure point in GE GTW-series and Adora top load washers — rods typically fail in pairs. Part WW01F01684 is the genuine OEM rear suspension rod that restores balanced drum support and eliminates vibration immediately.
❓ Is This the Right Part?
This is the correct fix if ALL of the following are true:
- ✔ Washer powers on and fills with water normally
- ✔ Agitator or impeller moves during the wash cycle
- ✔ Washer drains and spins — but shakes excessively or bangs
- ✔ Vibration is worst during the spin cycle at high RPM
- ✔ ONLY problem is excessive shaking, banging, or drum instability — not a no-spin or no-drain issue
Not sure? Send us your model number — we'll confirm before you order.
🔧 Common Symptoms
- Washer shakes violently or walks across the floor during spin
- Loud banging or clunking noise during spin cycle
- Drum visibly tilted or sitting lower on one side
- Washer stops mid-cycle due to out-of-balance detection
- Cabinet panels rattling or flexing during operation
- Clothes coming out wetter than normal — spin not completing
✔ If these symptoms match, this is the most likely failed component in the system.
✔ In most cases, replacing the rear suspension rod(s) restores smooth, balanced operation immediately.
📦 Part Details
- Part Number: WW01F01684
- Type: Rear suspension rod — spring-loaded strut that supports and dampens drum movement (sold individually)
- Replaces: 233D2080G004 — no modification required
- Brands: GE, GE Adora, GE Profile
⚙️ Installation Notes
Skill Level: EASY — 20–30 minutes. Disconnect power before servicing. Open the washer lid and remove the top panel or cabinet (model-dependent). The rear suspension rods hook into mounting points on the top frame and the outer tub — unhook the old rod, hook in the new one. No tools required for most models. Replace all four rods at the same time — if one has failed, the others are at the same wear stage and will fail shortly after.
💡 Pro Tip
Always Replace All Four Rods Together:
Suspension rods wear at the same rate. If one rear rod has snapped or lost its spring tension, the two front rods (WW01F01683) and the remaining rear rod are close behind. Replacing all four in one visit costs a fraction of a second service call and guarantees balanced drum support. Order WW01F01683 for the front pair.
Suspension rods wear at the same rate. If one rear rod has snapped or lost its spring tension, the two front rods (WW01F01683) and the remaining rear rod are close behind. Replacing all four in one visit costs a fraction of a second service call and guarantees balanced drum support. Order WW01F01683 for the front pair.
GTW460BMM0WW, GTW460BMK0WW, GTW465BMM0WS, GTW465BMK0WS, GTW485BMM0WS, GTW485BMK0WS, GTW490BMR0WS, GTW495DMN0WS, GTW550BMR0WS, GTW560BMM0WW, GTW575BMM0WS, GTW580BMR0WS, GTW680BMM0WS, GTW680BMK0WS, GTW680BMR0WS, GTW685BMR0WS, GTW690BMT0DG, GTW451BMR0WS, GTW470BMM0DG, GTW680BMM0DG
✅Compatibility & Cross Reference
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
Buy Online Pick Up In-Store
Address
101 Trillium Dr
Kitchener, Ontario N2E 1W8
Kitchener, Ontario N2E 1W8
Phone
Hours
Mon–Fri 9 AM–5 PM • Sat 9 AM–1 PM
- Choosing a selection results in a full page refresh.
