Menu
Electrolux Dryer Drum Not Spinning? Drive Belt 809183801 – Fix Drum Failure Fast
If your Electrolux or Frigidaire dryer runs but the drum sits completely still, the drive belt has almost certainly snapped or worn through. In most Electrolux and Frigidaire front-load dryers, this is caused by a failed drive belt. When it fails, the motor continues to run but the drum does not rotate — clothes stay wet regardless of cycle length. ⚡ Common failure point in Electrolux-built dryers after extended use. Part 809183801 is the genuine OEM replacement that restores full drum rotation immediately with no modification required.
❓ Is This the Right Part?
This is the correct fix if ALL of the following are true:
- ✔ Your dryer powers on and the motor runs normally
- ✔ Heating and controls function correctly — only the drum is affected
- ✔ Power supply and door latch confirmed OK
- ✔ ONLY problem is the drum not spinning or spinning freely with no resistance
Not sure? Send us your model number — we'll confirm before you order.
🔧 Common Symptoms
- Dryer runs but drum does not spin
- Drum spins freely by hand with no resistance (belt snapped)
- Loud squealing, squeaking, or thumping noise before drum stopped turning
- Burning rubber smell from inside the dryer cabinet
✔ If these symptoms match, this is the most likely failed component in the system.
✔ In most cases, replacing this drive belt restores normal operation immediately.
📦 Part Details
- Part Number: 809183801
- Type: Dryer Drive Belt — Front-Load Drum Belt
- Replaces: 134503600, 134163500, 131686100, 5308956610
- Brands: Electrolux, Frigidaire, AEG, Gibson, Kelvinator, White-Westinghouse
⚠️ Recommended While Repairing:
While the dryer is open, inspect the idler pulley and drum support glides — these wear at the same rate as the belt. Replacing all three in one service call prevents a repeat breakdown within months and saves significant disassembly time on a future repair.
While the dryer is open, inspect the idler pulley and drum support glides — these wear at the same rate as the belt. Replacing all three in one service call prevents a repeat breakdown within months and saves significant disassembly time on a future repair.
⚙️ Installation
Skill Level: Moderate — 30–45 minutes. Disconnect power before servicing. Remove the front panel and drum to access the belt routing path. Loop the new belt around the drum, thread it through the idler pulley and motor pulley, then reassemble in reverse order. Ensure the belt ribs seat flat against the drum — a twisted or misrouted belt will cause immediate re-failure.
✓ Compatible Models
Confirmed compatible with EFME417SIW0, EFME517SIW0, EFME617SIW0, EFMG417SIW0, EFMG517SIW0, EFMG617SIW0, FAQE7001LW0, FAQG7001LW0, FASE7073LW0, FASG7073LW0, FCED3000ES0, FCGD3000ES0, AEQB6000ES, AEW6530CEG0 plus additional Electrolux and Frigidaire models. Contact us to verify your model number before ordering.
💡 Pro Tip
Order the Idler Pulley at the Same Time:
The idler pulley is the single most common companion failure with a worn drive belt. It's inexpensive, the dryer is already fully disassembled, and skipping it now often means a second repair call within 6 months. Save your customer the labour — replace both together.
The idler pulley is the single most common companion failure with a worn drive belt. It's inexpensive, the dryer is already fully disassembled, and skipping it now often means a second repair call within 6 months. Save your customer the labour — replace both together.
✅Compatibility & Cross Reference
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
Buy Online Pick Up In-Store
Address
101 Trillium Dr
Kitchener, Ontario N2E 1W8
Kitchener, Ontario N2E 1W8
Phone
Hours
Mon–Fri 9 AM–5 PM • Sat 9 AM–1 PM
- Choosing a selection results in a full page refresh.
