Menu
Frigidaire Washer Overfilling, Won’t Fill, or Stops Mid-Cycle? Fix Water Level Pressure Switch 134762010 Fast
A Frigidaire washer that overfills with water, won’t fill at all, or stops mid-cycle with no error has a failed water level pressure switch. In most Frigidaire and Electrolux top-load and front-load washers, the water level pressure switch is the pneumatic sensor that monitors tub water level and signals the control board when to stop filling and begin agitation — when it fails, the machine either never stops filling (overfill), never starts filling (no water), or stops mid-cycle because the board receives a false water level signal. ⚡ Common failure point in Frigidaire-built washers. Part 134762010 is the genuine OEM replacement that restores accurate water level sensing and normal cycle operation immediately.
❓ Is This the Right Part?
This is the correct fix if ALL of the following are true:
- ✔ Your washer powers on and the control panel responds normally
- ✔ The water inlet valve is confirmed functional (water enters the tub when valve is energized)
- ✔ The pressure hose connecting the switch to the tub is intact, not cracked or clogged
- ✔ The control board has been confirmed functional (no other error codes)
- ✔ ONLY problem is overfilling, no fill, or cycle stopping at the fill phase
Not sure? Send us your model number — we’ll confirm before you order.
🔧 Common Symptoms
- Washer overfills — water keeps entering tub past the normal fill level
- Washer won’t fill at all — cycle starts but no water enters the tub
- Cycle stops at the fill phase with no error code displayed
- Washer fills to incorrect level — too little water for load size selected
- Agitation never starts even though tub has water in it
- Washer drains immediately after filling before agitation begins
✔ If these symptoms match, the water level pressure switch is the most likely failed component in the system.
✔ In most cases, replacing this pressure switch restores normal fill and cycle operation immediately.
📦 Part Details
- Part Number: 134762010
- Type: Washer Water Level Pressure Switch (Pneumatic Tub Sensor)
- Replaces: Genuine Frigidaire OEM direct-fit pressure switch (no modification required)
- Brands: Frigidaire, Electrolux
⚠️ Check This Before Ordering:
Before replacing the switch, inspect the pressure hose that runs from the bottom of the tub to the switch port — a cracked, kinked, or clogged hose causes identical symptoms and costs a fraction of the switch. Blow through the hose to confirm it’s clear and check both ends for a tight seal before condemning the switch.
Before replacing the switch, inspect the pressure hose that runs from the bottom of the tub to the switch port — a cracked, kinked, or clogged hose causes identical symptoms and costs a fraction of the switch. Blow through the hose to confirm it’s clear and check both ends for a tight seal before condemning the switch.
⚙️ Installation
Skill Level: MODERATE — 20–40 minutes. Disconnect power before beginning. Access the pressure switch by removing the control panel or top panel depending on your model, disconnect the wire harness and pressure hose from the switch, and swap the switch. Reconnect the pressure hose securely — a loose hose connection will cause the same overfill or no-fill symptoms as a failed switch and is the most common post-repair issue.
✓ Compatible Models
Confirmed compatible with select Frigidaire and Electrolux washer models. Contact us with your model number to verify compatibility before ordering.
💡 Pro Tip
💡 Pro Tip — Test the Pressure Hose First:
Disconnect the pressure hose from the switch and blow gently into it — you should hear a faint click from the switch as pressure builds. If the switch clicks, it’s likely functional and the hose or tub air dome is the problem. If there’s no click at any pressure, the switch has failed and 134762010 is your fix. This 30-second test eliminates the most common misdiagnosis on Frigidaire washers.
Disconnect the pressure hose from the switch and blow gently into it — you should hear a faint click from the switch as pressure builds. If the switch clicks, it’s likely functional and the hose or tub air dome is the problem. If there’s no click at any pressure, the switch has failed and 134762010 is your fix. This 30-second test eliminates the most common misdiagnosis on Frigidaire washers.
✅Compatibility & Cross Reference
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
Buy Online Pick Up In-Store
Address
101 Trillium Dr
Kitchener, Ontario N2E 1W8
Kitchener, Ontario N2E 1W8
Phone
Hours
Mon–Fri 9 AM–5 PM • Sat 9 AM–1 PM
- Choosing a selection results in a full page refresh.
