W10163997, W10443241

59679553010, 59679553011, JFC2290REM00, JFC2290REM02, JFC2290REM03, JFC2290REP00, JFC2290REP02, JFC2290VEM1, JFC2290VEM2, JFC2290VEM3, JFC2290VEM4, JFC2290VEM5, JFC2290VEM6, JFC2290VEM7, JFC2290VEM8, JFC2290VEP1, JFC2290VEP10, JFC2290VEP2, JFC2290VEP3, JFC2290VEP4, JFC2290VEP5, JFC2290VEP6, JFC2290VEP7, JFC2290VEP8, JFFCF72DKL00, JFFCF72DKL01, KFCP22EXMP1, KFCP22EXMP2, KFCP22EXMP3, KFCP22EXMP4, KFCP22EXMP5, KFCS22EVBL1, KFCS22EVMS1, KFCS22EVMS2, KFCS22EVMS3, KFCS22EVMS4, KFCS22EVMS5, KFCS22EVMS6, KFCS22EVMS7, KFCS22EVMS8, KFCS22EVWH1, KRFC302EBL00, KRFC302EBS00, KRFC302EBS02, KRFC302ESS00, KRFC302ESS02, KRFC302ESS03, KRFC302EWH00

🧰 What You’ll Need

• 
  Phillips screwdriver
  
• 
  Flat putty knife or plastic pry tool
  
• 
  Warm water or a hair dryer
  
• 
  Clean cloth
  

⚙️ Step-by-Step Installation

1. 
   Unplug the Refrigerator
   
   Always disconnect power before beginning any repair.
   
2. 
   Remove the Old Gasket
   
   
   Open the refrigerator door fully.
   
   
   Pull back a corner of the gasket to find the retaining lip or screws.
   
   
   Use a screwdriver or gently pull the gasket out of the door groove.
   
   
   Work your way around until the gasket is completely free.
   
   
   
3. 
   Clean the Door Channel
   
   
   Use a damp cloth to wipe away any residue, debris, or mold.
   
   
   Make sure the channel is completely dry before installing the new seal.
   
   
   
4. 
   Soften the New Gasket
   
   
   Place the new gasket in warm water (not boiling) for 5–10 minutes to relax the rubber.
   
   
   Or gently warm it with a hair dryer to remove creases from packaging.
   
   
   
5. 
   Install the New Gasket
   
   
   Start at one top corner and press the inner lip into the channel.
   
   
   Work slowly around the door, pressing the gasket into place evenly.
   
   
   Make sure corners are seated tightly with no twists or folds.
   
   
   
6. 
   Check the Seal Fit
   
   
   Close the door and look for gaps.
   
   
   If gaps appear, warm that section slightly and press it tighter into the frame.
   
   
   A thin film of petroleum jelly on the hinge side can help the gasket seat better.
   
   
   
7. 
   Final Test
   
   
   Plug the refrigerator back in.
   
   
   Close the door and run your hand around the seal — you should not feel any cool air escaping.
   
   
   Wait a few hours; the gasket will fully conform to the door shape as it cools.
   
   
   

✅ Pro Tip

If your refrigerator door isn’t closing evenly after replacement, loosen and adjust the door hinges slightly to ensure a uniform seal all around.

❄️ Cooling Problems

• 
  Warm spots in the fridge or uneven temperatures.
  
• 
  Compressor running constantly because cold air is leaking out.
  
• 
  Food spoiling faster than usual.
  

💧 Moisture & Frost Buildup

• 
  Condensation or water droplets forming around the door seal.
  
• 
  Frost or ice buildup inside the refrigerator or freezer compartments.
  
• 
  Water pooling near the bottom of the fridge.
  

🚪 Door Not Closing Properly

• 
  The door pops open after closing the other side (common on French-door models).
  
• 
  Door needs extra force to close or doesn’t stay shut.
  
• 
  Gasket edges appear warped, cracked, or torn.
  

⚡️ Higher Energy Bills

• 
  Fridge must work harder to maintain temperature due to air leaks.
  
• 
  Energy efficiency drops noticeably.
  

👃 Unpleasant Odors

• 
  Leaks cause humidity to rise, leading to mold or mildew around the seal.
  
• 
  You may see black or gray residue on the gasket edges.