Refrigerator Not Staying Cold? Door Gasket W10917313 – Fix Air Leaks & Warm Fridge Fast

A worn or torn door gasket is one of the most overlooked reasons a refrigerator struggles to maintain temperature — and one of the easiest fixes. In most Whirlpool, KitchenAid, and JennAir French door refrigerators, a failed door gasket allows warm room air to continuously infiltrate the cabinet. When it fails, the compressor runs longer and harder to compensate, food spoils faster, and energy bills climb — all from a single failed rubber seal. ⚡ Common wear item in KRFC, WRF, and JFFCC series refrigerators. Part W10917313 is the genuine OEM replacement that restores a factory-tight door seal, stops warm air infiltration, and brings your refrigerator back to peak efficiency.

❓ Is This the Right Part?

This is the correct fix if ALL of the following are true:

• ✔ Your refrigerator runs and cools — compressor and fans are operating normally
• ✔ The interior light, controls, and ice maker (if equipped) work correctly
• ✔ You can feel warm air escaping around the door edge, or the gasket is visibly cracked, torn, or no longer sealing flat
• ✔ The ONLY problem is the door not sealing properly / refrigerator running warm or constantly

Not sure? Send us your model number — we'll confirm before you order.

🔧 Common Symptoms

• Refrigerator running constantly but not reaching set temperature
• Condensation or frost buildup around the door frame or inside the cabinet
• Visible cracks, tears, gaps, or hardening in the door seal rubber
• Warm air felt along the door edge when the door is closed
• Higher than normal energy consumption / compressor never cycling off
• Food spoiling faster than expected despite correct temperature settings

✔ If these symptoms match, the door gasket is the most likely failed component in the system.

✔ In most cases, replacing this door gasket restores a factory-tight seal and normal compressor cycling immediately.

📦 Part Details

• Part Number: W10917313
• Type: Refrigerator Fresh Food Door Gasket / Door Seal (Item #22 in diagram)
• Replaces: W10798100
• Brands: Whirlpool, KitchenAid, JennAir

⚙️ Installation

Skill Level: Easy — 20 to 40 minutes. Disconnect power before servicing. Open the refrigerator door and peel the old gasket away from the door liner, starting at a corner — it is held in place by the door liner retainer. Soak the new gasket in warm water for 10–15 minutes to make it pliable, then press it firmly into the retainer groove around the full perimeter of the door. Close the door and check for even contact all the way around. No tools required for most models.

✓ Compatible Models

Confirmed compatible with WRF954CIHZ00, WRF954CIHZ01, WRF954CIHZ02, WRF954CIHZ03, WRF954CIHW00, WRF954CIHV00, WRF954CIHM00, WRF954CIHB00, WRF974CIHZ00, WRF974CIHV00, WRF964CIHV00, WRF964CIHM00, KRFC804GSS00, KRFC804GPS00, KRFC804GBS00, KRFC704FSS00, KRFC704FSS01, KRFC704FSS02, KRFC704FSS03, KRFC704FPS00, KRFC704FPS01, KRFC704FPS03, KRFC704FPS04, KRFC704FBS00, KRFC704FBS01, KRFC704FBS02, KRFC704FBS03, KRFC604FSS00, KRFC604FSS01, KRFC604FSS02, KRFC604FSS03, JFFCC72EFS00, JFFCC72EFS02, JFFCC72EFS03, JFFCC72EFS04, JFFCC72EFP00, JFFCC72EFP02, JFFCC72EHL01, JFFCC72EHL02, plus additional Whirlpool-platform models. Contact us to verify your model number before ordering.

✓ Model-Specific Repair Pages

💡 Pro Tip