Washer Not Spinning Balanced? Suspension Rod Kit W11130356 – Fix Excessive Vibration Fast

Is your top-load washer shaking violently, banging during the spin cycle, or stopping mid-cycle with an unbalanced load error? In most Maytag and Whirlpool top-load washers, this is caused by worn or broken suspension rods. When they fail, the wash basket loses its dampened support, causing the tub to slam against the cabinet walls during agitation and spin. ⚡ Common failure point in Maytag- and Whirlpool-built top-load washers. Part W11130356 is the genuine OEM replacement suspension rod kit that restores proper basket stabilization and eliminates vibration immediately.

❓ Is This the Right Part?

This is the correct fix if ALL of the following are true:

• ✔ Your washer powers on and fills with water normally
• ✔ The agitator or impeller moves during the wash cycle
• ✔ Water supply and inlet valves are confirmed OK
• ✔ The drain pump and lid switch function correctly
• ✔ ONLY problem is excessive vibration, banging, or unbalanced load errors during spin

Not sure? Send us your model number — we'll confirm before you order.

🔧 Common Symptoms

• Washer shaking violently or walking across the floor during spin
• Loud banging or clunking noise during agitation or spin cycle
• Washer stops mid-cycle with an unbalanced load error
• Visible tub movement — basket visibly hitting the cabinet walls
• F0E5 or UL error code displayed on control panel
• One or more suspension rods visibly broken, bent, or detached

✔ If these symptoms match, the suspension rod kit is the most likely failed component in the system.

✔ In most cases, replacing all four suspension rods restores normal, quiet operation immediately.

📦 Part Details

• Part Number: W11130356
• Type: Washer Suspension Rod Kit — set of 4 rods with spring caps
• Replaces: OEM direct-fit suspension rod assembly — supersedes W10594084, W10735787, W10821706, W10901058, W11027214, W11033601 (no modification required)
• Brands: Maytag, Whirlpool, Kenmore

⚙️ Installation

Skill Level: EASY — 20–30 minutes. Unplug the washer before beginning. Remove the cabinet top or front panel to access the suspension rod mounting points at each corner of the outer tub; unhook the old rods and snap the new ones into place. Always replace all four rods as a set — mismatched rod stiffness will cause the same unbalanced symptoms to return.

💡 Pro Tip

Find your model's full parts list and repair guides: 11028132410, 11028132412, 11028132413, 11028132414, 11028133410, 11028133411, 11028133412, 11028133413, 11028133414, 11029132411, 11029132412, 11029132413, 11029133411, 11029133412, 11029133413, 7MMVWB835EW0, 7MMVWB835EW1, 7MMVWB855EC0, 7MMVWB855EC1, 7MMVWB855EC2, 7MMVWB855EC3, 7MWTW8500EC0, 7MWTW8500EC1, 7MWTW8500EC2, MVWB835DC0, MVWB835DC2, MVWB835DC3, MVWB835DC4, MVWB835DC5, MVWB835DW0, MVWB835DW1, MVWB835DW2, MVWB835DW3, MVWB835DW4, MVWB835DW5, MVWB855DC0, MVWB855DC1, MVWB855DC2, MVWB855DC3, MVWB855DC4, MVWB855DW0, MVWB855DW1, MVWB855DW2, MVWB855DW3, MVWB865GC0, MVWB865GC1, MVWB865GW0, MVWB865GW1, WTW8000DW0, WTW8000DW1, WTW8000DW2, WTW8000DW3, WTW8000DW4, WTW8000DW5, WTW8040DW0, WTW8040DW1, WTW8040DW2, WTW8040DW3, WTW8040DW4, WTW8500DC0, WTW8500DC1, WTW8500DC2, WTW8500DC3, WTW8500DC4, WTW8500DC5, WTW8500DC6, WTW8500DR0, WTW8500DR1, WTW8500DR2, WTW8500DR3, WTW8500DR4, WTW8500DR5, WTW8500DW0, WTW8500DW1, WTW8500DW2, WTW8500DW3, WTW8500DW4, WTW8500DW5, WTW8500DW6, WTW8700EC0, WTW8700EC1

✓ Model-Specific Repair Pages