Gas Range Burners Not Igniting? Spark Module W11162730 – Fix Ignition Failure Fast
When gas range burners won't ignite, click continuously without sparking, or only some burners fire, the spark module is the most common cause. In most Whirlpool, Maytag, and KitchenAid gas ranges, the spark module generates timed high-voltage pulses to the igniter electrodes at each burner — when it fails, one or all burners lose ignition entirely, click without producing a spark, or fire intermittently with no pattern. ⚡ Common failure point in Whirlpool-built gas ranges after moisture ingress, electrical surges, or age-related component failure. Part W11162730 is the genuine OEM replacement module that restores reliable ignition to all burners immediately.
❓ Is This the Right Part?
This is the correct fix if ALL of the following are true:
- ✔ Gas supply is confirmed on — other gas appliances in the home work normally
- ✔ Igniter electrodes and spark wires are intact with no visible cracks or corrosion
- ✔ Range powers on and the oven functions normally
- ✔ Burner caps and heads are clean and seated correctly
- ✔ ONLY problem is one or more burners won't ignite, click without sparking, or fire intermittently
Not sure? Send us your model number — we'll confirm before you order.
🔧 Common Symptoms
- Gas burners won't ignite — no click, no spark, no flame
- Continuous clicking at one or all burners with no spark produced
- Only some burners ignite — others are completely dead
- Burners ignite intermittently — sometimes work, sometimes don't
- Clicking continues after burner is lit and knob is released
- No clicking sound at all when burner knob is turned to ignite
✔ If these symptoms match, this is the most likely failed component in the system.
✔ In most cases, replacing this spark module restores reliable ignition to all burners immediately.
📦 Part Details
- Part Number: W11162730
- Type: Oven Spark Module — multi-outlet ignition control board (solid-state)
- Replaces: OEM direct-fit spark module for compatible Whirlpool-built gas ranges (no modification required)
- Brands: Whirlpool, Maytag, KitchenAid, Amana, JennAir
While the module is out, inspect all igniter electrodes and spark wires for cracks, corrosion, or carbon tracking — a damaged electrode will prevent the new module from producing a spark and will cause a repeat no-ignition complaint. Replace any cracked or corroded electrodes at the same time.
⚙️ Installation Notes
Skill Level: MODERATE — 20–30 minutes. Disconnect power AND shut off the gas supply before beginning any repair on a gas range. Remove the cooktop or access panel to reach the spark module, photograph all wire harness connections before disconnecting, then swap the module and reconnect all wires in the original positions. Restore power and test each burner individually before reassembling. Never operate the range with the gas supply on and the cooktop removed.
✓ Compatible Models
This spark module fits specific Whirlpool-built gas range models. Contact us with your model number to confirm compatibility before ordering — we'll verify the fit for you.
💡 Pro Tip
Moisture is the #1 cause of spark module failure — boil-overs and steam from cooking seep under the cooktop and corrode the module's solid-state circuitry. Before installing the new module, dry the area thoroughly with a cloth and let it air out for 30 minutes. If the module fails again within a year, inspect the cooktop seal and burner cap gaskets for gaps that allow moisture ingress.
✓ Model-Specific Repair Pages
✅Compatibility & Cross Reference
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
Buy Online Pick Up In-Store
Kitchener, Ontario N2E 1W8
- Choosing a selection results in a full page refresh.
