Dishwasher Leaking From the Door? Fix Tub Gasket WG04F01096 Fast – Limited Stock
A dishwasher that leaks water onto the floor during or after a cycle has a failed tub door gasket. In most GE GLDA and GHDA series dishwashers, the tub gasket is the rubber seal that runs the full perimeter of the door opening — when it cracks, tears, or loses compression, water escapes the tub and pools on the floor in front of the machine. ⚡ Age-related hardening and cracking is the most common failure mode in GE-built dishwashers of this era. Part WG04F01096 is the genuine OEM replacement (supersedes WD08M00037) — this part is No Longer Available from the manufacturer, so stock is limited and will not be replenished.
❓ Is This the Right Part?
This is the correct fix if ALL of the following are true:
- ✔ Your dishwasher is a GE GLDA or GHDA series model
- ✔ Water appears on the floor directly in front of the dishwasher during or after a cycle
- ✔ The leak is coming from the door area, not from underneath the machine
- ✔ The door closes and latches normally (door latch is not the issue)
- ✔ ONLY problem is water leaking from the door perimeter during wash or rinse
Not sure? Send us your model number — we’ll confirm before you order.
🔧 Common Symptoms
- Water pooling on the floor in front of the dishwasher during a cycle
- Visible crack, tear, or deformation in the door seal gasket
- Gasket feels hard, brittle, or no longer compresses when door closes
- Water marks or mineral deposits on the floor after cycles complete
- Door feels like it doesn’t seal tightly even when fully latched
- Leak worsens during high-pressure wash phases but stops during dry cycle
✔ If these symptoms match, the tub door gasket is the most likely failed component in the system.
✔ In most cases, replacing this gasket stops the leak immediately.
📦 Part Details
- Part Number: WG04F01096
- Type: Dishwasher Tub Door Gasket (Full Perimeter Seal)
- Replaces: OEM direct-fit tub gasket — supersedes WD08M00037 (no modification required)
- Brands: GE
- Availability: No Longer Available (NLA) — limited remaining stock only. Contact us to confirm before ordering.
⚙️ Installation
Skill Level: EASY — 15–30 minutes. Disconnect power before beginning. Open the dishwasher door and pull the old gasket out of the channel starting at one corner, working around the full perimeter. Clean the channel thoroughly to remove any debris or old gasket material. Press the new gasket firmly into the channel starting at the top center and working outward to each side, then down — ensure no gaps or lifted sections remain. Run a short cycle and inspect for leaks before closing up. Handle with care — as an NLA part, this gasket cannot be replaced if damaged during installation.
✓ Compatible Models
Confirmed compatible with GLDA696, GLDA690, GHDA696, GHDA690, GLDA696F, GLDA690F, GLDA690M, GCD4800L, GLFS1474 series and additional GE GLDA/GHDA variants. Contact us to verify your model number before ordering.
💡 Pro Tip
Before ordering this NLA part, confirm the leak is coming from the door gasket and not from a pump seal, inlet valve, or drain hose — leaks from underneath the machine look similar on the floor but require a completely different repair. Run a cycle and watch where the water first appears: door area = gasket, from below = internal component. Since this part cannot be restocked, accurate diagnosis before ordering is critical.
GLDA696M00SS, GLDA690P01BB, GHDA696P03SS, GHDA690P02BB, GLDA690M02BB, GLDA696P03SS, GHDA696P04SS, GCD4800L00WW, GLDA690M00SS, GLFS1474XSS
✅Compatibility & Cross Reference
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
Buy Online Pick Up In-Store
Kitchener, Ontario N2E 1W8
- Choosing a selection results in a full page refresh.
