Range Burner Not Heating Correctly? Surface Element Switch WP74010824 — Fix It Fast
If a burner on your electric range won't heat, heats only on one setting, or won't turn off, the surface element switch is the most common cause. In most Whirlpool-built electric ranges, the infinite switch wears out internally — losing the ability to regulate current to the burner coil at different heat levels. When it fails, the burner may stay stuck on high, refuse to heat at all, or only respond at certain settings. ⚡ Common failure point in Whirlpool, Kenmore, Jenn-Air, KitchenAid, and Maytag electric ranges. Part WP74010824 is the genuine OEM replacement switch that restores full infinite heat control — from simmer to high — on your range's surface elements.
❓ Is This the Right Part?
This is the correct fix if ALL of the following are true:
- ✔ Your range powers on and the clock/display works normally
- ✔ Other burners on the range heat correctly
- ✔ The outlet and breaker supplying the range are confirmed OK
- ✔ ONLY problem is one burner won't heat, heats on one level only, or won't shut off
Not sure? Send us your model number — we'll confirm before you order.
🔧 Common Symptoms
- Burner element won't heat on any setting
- Burner stays stuck on high and won't reduce heat
- Burner only works on one heat level (e.g., only high or only low)
- Burner won't turn off when the knob is turned to OFF
✔ If these symptoms match, this is the most likely failed component — the switch, not the element itself.
✔ In most cases, replacing the surface element switch restores full infinite heat control immediately.
📦 Part Details
- Part Number: WP74010824
- Type: OEM Infinite Surface Element Switch (Burner Control Switch) for Electric Range / Cooktop
- Replaces: 74010824, 7450P011-60
- Brands: Whirlpool, Kenmore, Amana, Jenn-Air, KitchenAid, Maytag
While the switch is out, inspect the burner element for cracks, burn marks, or broken coil ends. A damaged element can burn out a new switch prematurely. If the element shows any visible damage, replace both at the same time — you're already in there.
⚙️ Installation
Skill Level: MODERATE — 30–45 minutes. Basic tools required. Disconnect power at the breaker before servicing. Remove the range's back panel or lift the cooktop to access the switch bank. Photograph the wiring harness connections before disconnecting. Remove the old switch, install WP74010824, reconnect the harness, reassemble, and restore power to test all heat settings.
✓ Compatible Models
Confirmed compatible with hundreds of Whirlpool-platform electric ranges including: AES5730BAB, GGE388LXQ00, GGE390LXQ00, GY397LXUQ0, GY399LXUQ0, JES8850CAS00, JES9800CAS00, JES9900CCS00, KERS205TSS0, KERS505XSS00, MER6775BAB, MES5875BAS, MET8665XB00, YMET8720DE00, YMET8885XB00, WDE350LVB0, and many more Kenmore, Jenn-Air, KitchenAid, and Maytag models. Contact us to verify your model number before ordering.
💡 Pro Tip
Use a multimeter to test the burner element for continuity before ordering. If the element reads open (no continuity), the element is the problem — not the switch. If the element tests good but the burner still misbehaves, the switch is the confirmed culprit. This 2-minute test prevents replacing the wrong part.
✓ Shop by Appliance Type
✅Compatibility & Cross Reference
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
Buy Online Pick Up In-Store
Kitchener, Ontario N2E 1W8
- Choosing a selection results in a full page refresh.
