Whirlpool Front Load Washer Leaking from Door? Door Bellow WP8182119 – Fix Door Seal Failure Fast
A front-load washer that leaks water from the door during every wash cycle almost always has a torn, cracked, or punctured door bellow (door boot seal). In most Whirlpool and Maytag front-load washers, the door bellow is the large rubber gasket that seals the gap between the drum and the door glass — when it tears, splits, or develops holes, water escapes onto the floor with every load. When it fails, the washer may also trap mold and debris in the folds, causing odour and potential drum damage. ⚡ Common failure point in Whirlpool-built front-load washers — especially in high-use households. Part WP8182119 is the genuine OEM replacement door bellow that restores a watertight drum seal and eliminates door leaks immediately.
❓ Is This the Right Part?
This is the correct fix if ALL of the following are true:
- ✔ Your Whirlpool or Maytag front-load washer leaks water from the front door during the wash or spin cycle
- ✔ The washer fills, agitates, and spins normally — only the door seal is the issue
- ✔ The door latch and door glass are intact — the rubber gasket is visibly torn, cracked, or has holes
- ✔ ONLY problem is water leaking from the door — no error codes or drum issues
Not sure? Send us your model number — we'll confirm before you order.
🔧 Common Symptoms
- Water pooling on the floor in front of the washer during or after a cycle
- Visible tear, crack, split, or hole in the rubber door gasket
- Mold or mildew growing in the folds of the door bellow that won’t clean off
- Musty smell coming from the washer door area
- Small objects (coins, socks) getting trapped between the bellow and the drum
- Water dripping from the bottom of the door glass when the door is opened
✔ If these symptoms match, this is the most likely failed component in the system.
✔ In most cases, replacing this door bellow eliminates door leaks and restores a clean, watertight seal immediately.
📦 Part Details
- Part Number: WP8182119
- Type: Front Load Washer Door Bellow / Boot Seal
- Replaces: 8182119, W10003800 — no modification required
- Brands: Whirlpool, Maytag, KitchenAid, Kenmore
While the door bellow is off, inspect the door latch assembly and the drain pump filter. A torn bellow often traps debris that can clog the pump filter — and a worn door latch that doesn’t close firmly will stress the new bellow and cause premature tearing. Clean the filter and test the latch before reassembling to avoid a repeat repair.
⚙️ Installation
Skill Level: Moderate — 45–60 minutes. Disconnect power before servicing. Remove the front panel and door latch to release the bellow retaining spring clamp at the front, then reach behind the drum to release the rear clamp. Pull the old bellow free, clean the drum lip thoroughly, and seat the new bellow starting at the drain port at the bottom. Reinstall the front spring clamp using a flat-blade screwdriver or bellow clamp tool, then reassemble the front panel and run a short cycle to confirm no leaks before closing up.
✓ Compatible Models
Confirmed compatible with GHW9150PW0, GHW9300PW0, GHW9400PW0, GHW9460PW0, WFW9200SQ00, WFW9400SW00, WFW9450WW00, WFW9470WW00, WFW9500TW00, WFW9550WW00, WFW9600TW00, WFW9750WW00, MHWE300VW00, MHWE400WW00, MHWE450WW00, MHWE550WW00, MHWE900VW00, MHWE950WW00 plus additional Whirlpool, Maytag, KitchenAid, and Kenmore front-load washer models. Contact us to verify your model number before ordering.
WFW9200SQ00, WFW9200SQ01, WFW9200SQ02, WFW9200SQ03, WFW9200SQ04, WFW9200SQ10, WFW9400SB00, WFW9400SB01, WFW9470WL00, WFW9470WL01, WFW9470WR00, WFW9470WR01, WFW9470WW00, WFW9470WW01, WFW9500TC00, WFW9500TC01, WFW9500TC02, WFW9500TC03, WFW9500TW00, WFW9500TW01, WFW9500TW02, WFW9500TW03, WFW9550WL10, WFW9550WW10, WFW9600TA00, MHWE300VW10, MHWE300VW11, MHWE300VW12, MHWE300VW13, MHWE950WW02
💡 Pro Tip
The front spring clamp on this bellow is under significant tension and is the #1 cause of failed DIY installs. Without a proper bellow clamp tool or large flat-blade screwdriver, the clamp won’t seat evenly and the bellow will leak from day one. A bellow clamp tool costs under $15 and makes the difference between a 45-minute job and a 3-hour frustration. If you’re ordering the bellow, order the tool at the same time.
✅Compatibility & Cross Reference
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
Buy Online Pick Up In-Store
Kitchener, Ontario N2E 1W8
- Choosing a selection results in a full page refresh.
