KitchenAid Oven Not Heating or Baking Unevenly? Bake Element WP9750213 – Fix Lower Element Failure Fast
A burned-out bake element is the most common cause of a KitchenAid or Whirlpool oven that won’t heat, takes too long to preheat, or bakes unevenly with food undercooked on the bottom. In KitchenAid KERC, KESC, KESH, and KERS series ranges and Whirlpool GR, GY, WGE, and WLE series ranges, the lower bake element is the primary heat source for all baking functions — it draws 2500W and cycles on and off to maintain the selected oven temperature. When the element burns through, cracks, or develops a visible break in the coil, the oven loses its primary heat source entirely. ⚡ Most common single-point failure in KitchenAid and Whirlpool electric ranges — bake elements fail from thermal cycling stress over time. Part WP9750213 is the genuine OEM replacement that restores full 2500W baking performance immediately — direct plug-in fit, no wiring modifications required.
❓ Is This the Right Part?
This is the correct fix if ALL of the following are true:
- ✔ Range powers on and the broil element or stovetop burners work normally
- ✔ The oven control board and temperature sensor have been ruled out as the failure source
- ✔ Power supply to the range is confirmed at full 240V
- ✔ ONLY problem is the oven won’t heat, preheats slowly, or bakes unevenly on the bottom
Not sure? Send us your model number — we'll confirm before you order.
🔧 Common Symptoms
- Oven not heating at all on bake mode — most common complaint
- Oven takes excessively long to reach set temperature
- Food undercooked on the bottom — uneven baking results
- Visible burn mark, blister, crack, or break in the element coil inside the oven cavity
- Oven trips the breaker when attempting to bake
- Element glows red on one section only — partial failure
✔ If these symptoms match, the bake element is the most likely failed component in the system.
✔ In most cases, replacing WP9750213 restores full oven heating performance immediately.
📦 Part Details
- Part Number: WP9750213
- Type: Oven Lower Bake Element — 2500W coil-type heating element for KitchenAid and Whirlpool electric ranges
- Replaces: 975-0213, 9750213, 9750213A, TJ9750213A, CH0213, UB700, AP9750213
- Brands: KitchenAid, Whirlpool, Inglis, Estate, Roper
- Note: Available in OEM (WP9750213) and XPart aftermarket (WP9750213XP) options. XPart parts are not affiliated with or endorsed by KitchenAid or Whirlpool.
If the oven was running significantly hotter or cooler than the set temperature before the element failed, the oven temperature sensor (RTD probe) may also be out of spec. A faulty sensor causes the new element to cycle incorrectly and can shorten its life. Test the sensor resistance at room temperature (should read approximately 1080Ω at 70°F) before reassembling.
⚙️ Installation
Skill Level: EASY — 15–20 minutes. Disconnect power at the breaker before beginning. Open the oven door and remove the oven racks for clear access to the element. Remove the two mounting screws at the back of the oven cavity, gently pull the element forward to expose the wire connectors, and disconnect them. Connect the wires to the new WP9750213, slide it into position, reinstall the mounting screws, replace the racks, restore power, and run a bake cycle to confirm full heating.
✓ Compatible Models
Confirmed compatible with KERC500EAL1, KERC507EAL1, KERC600EAL0, KERC601HBT0, KERC607EAL0, KERC700LBL0, KESC300BAL1, KESC307BAL1, KESH307BAL1, KERS507EAL1, GR450LXHB0, GY395LXGB0, GY396LXGB0, TES400PXHB0, WGE30302, WLE30300, WLP30800 plus additional KitchenAid, Whirlpool, Inglis, and Estate electric range models. Contact us to verify your model number before ordering.
💡 Pro Tip
The bake element has two spade connectors that can retract into the back wall of the oven cavity if released without being held. If a connector falls back into the wall, accessing it requires removing the back panel — a 45-minute job that turns a 15-minute repair into an hour-long one. Hold each connector firmly while disconnecting and immediately connect it to the new element before releasing the other side.
✅Compatibility & Cross Reference
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
Buy Online Pick Up In-Store
Kitchener, Ontario N2E 1W8
- Choosing a selection results in a full page refresh.
