Heating Element Assembly, Heater Assembly, Dryer Heater, Electric Heating Element, Heating Coil Assembly, Complete Heater Housing Unit

WR01F02479, WR01F02479A, WR01F02479B, AP6331670, PS12745416, EAP12745416

GE, Hotpoint

GEGTD33EASK0WW, GTD33EASK1WW, GTD33EASK2WW, GTD33GASK0WW, GTD33GASK1WW, GTD33GASK2WW, GTD42EASJ0WW, GTD42EASJ1WW, GTD42EASJ2WW, GTD42GASJ0WW, GTD42GASJ1WW, GTD42GASJ2WW, GTD45EASJ0WW, GTD45EASJ1WW, GTD45EASJ2WW, GTD45GASJ0WW, GTD45GASJ1WW, GTD45GASJ2WW, GTD65EBSJ0DG, GTD65EBSJ1DG, GTD65EBSJ2DG, GTD65GBSJ0DG, GTD65GBSJ1DG, GTD65GBSJ2DG, GTD72EBSN0DG, GTD72EBSN1DG, GTD72EBSN2DG, GTD72GBSN0DG, GTD72GBSN1DG, GTD72GBSN2DG, GTD75ECPLDG, GTD75GCPLDG, GTD76ECPLDG, GTD76GCPLDG

HotpointHTX24EASK0WW, HTX24EASK1WW, HTX24EASK2WW, HTX24GASK0WW, HTX24GASK1WW, HTX24GASK2WW, HTX27EASK0WW, HTX27EASK1WW, HTX27EASK2WW, HTX27GASK0WW, HTX27GASK1WW, HTX27GASK2WW

Professional Repair Time: 30-45 minutes
DIY Repair Time: 60-90 minutes
Difficulty Rating: Moderate-Advanced (3.5/5) — Requires advanced mechanical and electrical skills, dryer disassembly, 240V electrical knowledge, multimeter testing, careful wire handling

CRITICAL SAFETY WARNING: This repair involves 240V electrical connections. Always turn off the circuit breaker before beginning work. If uncomfortable with electrical systems, hire a qualified technician.

1. Turn off the circuit breaker supplying power to the dryer at the main electrical panel.
2. Unplug the dryer (if accessible) for additional safety.
3. Verify power is off using a non-contact voltage tester.
4. Disconnect the exhaust vent hose from the rear of the dryer.
5. Pull the dryer away from the wall to access the rear panel.
6. Take multiple photos of the heating element installation and all wire connections before disassembly.
7. Remove the rear access panel (typically 6-10 Phillips screws around perimeter).
8. Label all wire connections with tape indicating positions (L1, L2, thermostat, thermal fuse).
9. Take detailed photos of wire colors and terminal positions.
10. Disconnect all electrical wires by removing spade connectors or loosening screw terminals. Grip connectors, not wires.
11. Remove heating element mounting screws (typically 2-4 screws).
12. Carefully remove the old heating element from the cabinet. Wear gloves—housing may have sharp edges.
13. Inspect the old element for broken coil, blown thermal fuse, corroded terminals, or damaged housing.
14. Test the old element with a multimeter set to measure resistance. Should read 8-12 ohms between power terminals. Infinite reading = broken coil. Test for continuity to housing (ground)—should be infinite (no short circuit).
15. Test thermal fuse and thermostat for continuity—both should show continuity when cool.
16. Inspect exhaust vent system thoroughly for blockages. CRITICAL: Blocked vents are the #1 cause of element failure. Clean entire vent from dryer to outside cap.
17. Clean blower housing and wheel to remove lint buildup.
18. Inspect heating element mounting area and clean if necessary.
19. Unpack the new WR01F02479 heating element carefully.
20. Compare new element to old to verify dimensions, terminal positions, and mounting holes match.
21. Inspect new element for any shipping damage.
22. Test new element with multimeter (optional)—should read 8-12 ohms, no continuity to housing.
23. Position new element in cabinet, aligning mounting holes and ensuring terminals are accessible.
24. Install mounting screws and tighten firmly but not excessively.
25. Verify element is securely mounted with no movement.
26. Reconnect all electrical wires according to photos and labels. Push spade connectors firmly onto terminals. CRITICAL: Incorrect wiring creates fire hazards.
27. Verify all connections are secure by gently tugging each wire.
28. Double-check all wire connections against photos.
29. Ensure no wires touch the heating element housing or hot surfaces.
30. Reinstall rear access panel and tighten screws in cross-pattern.
31. Reconnect exhaust vent hose and secure with hose clamp.
32. Push dryer back toward wall, leaving 4-6 inches clearance.
33. Restore power by turning on circuit breaker.
34. Plug in dryer (if unplugged).
35. Run test cycle (timed dry, high heat) for 3-5 minutes.
36. Verify heating—open door briefly and feel for warm/hot air in drum.
37. Listen for unusual noises—should operate smoothly.
38. Check outside vent cap for strong, warm air flow.
39. Monitor temperature during first 10-15 minutes—element should cycle on/off.
40. Run complete drying cycle with small load to verify proper drying performance.
41. If element operates properly and clothes dry effectively, repair is complete.

Safety Notes: Always turn off circuit breaker before working on 240V systems. Clean exhaust vents before installing new element. Label all wires before disconnecting. Take detailed photos. Test element with multimeter to confirm failure. Do not overtighten screws or terminals. This repair requires advanced mechanical and electrical skills.

1. Always clean the exhaust vent system before replacing the heating element—blocked vents cause 90% of element failures. Clean from dryer to outside vent cap and verify strong air flow.
2. Test the element with a multimeter before replacement. Should read 8-12 ohms between power terminals. Infinite = broken coil. Also test for shorts to housing—should be infinite resistance.
3. The element operates at 240V AC and draws 20-25 amps—correct wiring is critical. Label all wires and take detailed photos before disconnecting. Incorrect wiring causes fire hazards.
4. The high-limit thermal fuse (250°F-280°F) is a one-time safety device. Once blown, it must be replaced. If it blows repeatedly, fix the root cause (blocked vent, blower failure) first.
5. The operating thermostat (130°F-150°F) cycles the element on/off. If stuck closed, dryer overheats. If stuck open, no heating occurs.
6. Verify the element is firmly mounted before connecting wires. Loose elements vibrate and cause wire connection failures.
7. The nichrome coil must never touch the metal housing—this causes immediate short circuit failure. Ceramic insulators prevent contact. Inspect before installation.
8. Heating elements typically last 8-12 years with proper maintenance. Blocked vents, overloading, and dirty lint filters shorten element life significantly.
9. Monitor the dryer during first few cycles after replacement. Check for proper heating, normal cycling, no unusual noises, and proper drying time (30-60 minutes).
10. The complete assembly includes housing, coil, thermal fuse, and thermostat—all replaced together. More reliable than replacing individual components.

• Dryer not heating at all
• Dryer heating intermittently or cycling rapidly
• Dryer overheating or getting too hot
• Clothes taking too long to dry
• Dryer tripping circuit breaker
• Burning smell during operation
• Thermal fuse repeatedly blowing
• Heating element coil broken or burned
• Visible damage to element housing
• Error codes indicating heating fault
• Weak or insufficient heat
• Temperature not reaching proper level
• Dryer running but producing no heat
• Short circuit to housing
• Corroded electrical terminals
• Thermostat failure
• Insulator damage