Whirlpool Corporation 6-foot dishwasher drain hose W11414944

Genuine OEM 6-foot external dishwasher drain hose used to connect a dishwasher drain outlet to the sink drain or disposal. The hose is manufactured for Whirlpool Corporation appliance brands, including KitchenAid.

❓ Is This the Right Part?

This is the correct fix if ALL of the following are true:

• ✔ Dishwasher powers on and runs cycles normally
• ✔ Wash and rinse functions work correctly — only draining fails or water is leaking from under the unit
• ✔ Drain filter and sump are clean and unobstructed
• ✔ Garbage disposal or sink drain connection is clear and functional
• ✔ ONLY problem is standing water in the tub, a drain error code, or water leaking from under the dishwasher during or after the drain cycle

Not sure? Send us your model number — we’ll confirm before you order.

🔧 Common Symptoms

• Dishwasher not draining — standing water in the bottom of the tub after the cycle ends
• Drain cycle runs but water level doesn’t drop
• Water leaking under or beside the dishwasher during or after the drain cycle
• Wet floor under the sink cabinet — hose leaking at the pump or drain connection
• Dishwasher stops mid-cycle with a drain error (e.g. F8E1 or similar)
• Gurgling sounds or dirty water backing up into the tub between cycles

✔ If these symptoms match, the drain hose is the most likely failed component in the system.

✔ In most cases, replacing the drain hose restores normal drain operation immediately.

✅ Cross Reference Information

Part Details

• Part Number: W11414944
• Part Type: 6-foot dishwasher drain hose
• Manufacturer: Whirlpool Corporation
• Appliance Type: Dishwasher

⚙️ Installation

Skill Level: MODERATE — 20 to 40 minutes. Disconnect power at the breaker and turn off the water supply before starting. Access the drain hose from under the sink at the disposal or drain connection and from inside the dishwasher toe-kick panel. Photograph the hose routing and clamp positions before removing — the new hose must follow the identical path. Loosen clamps at both ends, slide the old hose off, and route the new W11414944 in the same path. High-loop installation required: route the hose up as high as possible under the counter before dropping to the drain connection to prevent backflow — secure the loop with a cable tie to the underside of the counter. Tighten all clamps, restore power and water, and run a short cycle while watching both connection points for leaks.

💡 Pro Tip

🔗 Model Repair Pages

KDFE104KBL0, KDFE104KPS0, KDFE104KWH0, KDFE204KBL0, KDFE204KBS0, KDFE204KPS0, KDFE204KWH0, KDFM404KBS0, KDFM404KPS0, KDPM604KBS0, KDPM604KPS0, KDPM704KPS0, KDPM804KBS0, KDPM804KPS0, KDTE104KPS0, KDTE204KBL0, KDTE204KBS0, KDTE204KPS0, KDTE204KWH0, KDTM404KBS0, KDTM404KPS0, KDTM604KBS0, KDTM604KPS0, KDTM704KPS0, KDTM804KBS0, KDTM804KPS0, MDB4949SKB0, MDB4949SKW0, MDB4949SKZ0, MDB7959SKZ0, MDB8959SKB0, MDB8959SKK0, MDB8959SKW0, MDB8959SKZ0, MDB9959SKZ0, MDB9979SKZ0, WDT750SAKB0, WDT750SAKV0, WDT750SAKW0, WDT750SAKZ0, WDTA50SAKB0, WDTA50SAKT0, WDTA50SAKV0, WDTA50SAKW0, WDTA50SAKZ0, WDTA80SAKZ0

Verified Compatible Models

✓ Model-Specific Repair Pages