Control Knob, Burner Knob, Range Knob, Cooktop Knob, Surface Burner Knob, Temperature Control Knob

Part number W11517331 replaces W10850027, W11117415, W11458840

Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Kenmore, Roper, Admiral, Inglis

WEE745H0FE0, WEE745H0FE1, WEE745H0FE2, WEE745H0FH0, WEE745H0FH1, WEE745H0FH2, WEE745H0FS0, WEE745H0FS1, WEE745H0FS2, WFE745H0FE0, WFE745H0FE1, WFE745H0FH0, WFE745H0FH1, WFE745H0FS0, WFE745H0FS1, WFE745H0FS2, WFE770H0FZ0, WFE770H0FZ1, WFE770H0FZ2, YWEE745H0FE0, YWEE745H0FE1, YWEE745H0FH0, YWEE745H0FH1, YWEE745H0FS0, YWEE745H0FS1, YWEE745H0FS2, YWFE745H0FE0, YWFE745H0FE1, YWFE745H0FH0, YWFE745H0FH1, YWFE745H0FH2, YWFE745H0FS0, YWFE745H0FS1, YWFE745H0FS2, YWFE770H0FZ0

SAFETY NOTE: This is a simple cosmetic repair that does not require power disconnection or tools. However, ensure the range is cool before handling knobs to avoid burns.

1. Allow the range to cool completely if it has been used recently. Wait at least 30 minutes after cooking.
2. Take a photo of the existing knob position and orientation for reference.
3. Locate the control knob that needs replacement on the range control panel.
4. Grasp the old knob firmly with your hand, gripping the outer edge.
5. Pull the knob straight out away from the control panel with steady, firm pressure. The knob should slide off the valve stem. Note: Some knobs may require slight wiggling or rocking motion while pulling to release from the stem.
6. If the knob is stuck, try gently rocking it side-to-side while pulling outward. Do not use excessive force—this can damage the valve stem.
7. Remove the old knob completely from the valve stem and set aside.
8. Inspect the valve stem (the metal or plastic shaft protruding from the control panel). Note the shape—it should be D-shaped (flat on one side) or have a flat-sided profile.
9. Clean the valve stem with a damp cloth to remove any grease, food residue, or debris. Dry thoroughly.
10. Unpack the new W11517331 control knob from its packaging.
11. Inspect the new knob for any damage before installation.
12. Examine the internal shaft opening on the back of the new knob. It should have a D-shaped or keyed opening that matches the valve stem shape.
13. Align the knob shaft opening with the valve stem, matching the flat side of the opening with the flat side of the stem. Important: Proper alignment is critical—the knob will only fit one way.
14. Push the knob straight onto the valve stem with firm, steady pressure until it seats completely against the control panel. The knob should slide on smoothly and sit flush with the panel.
15. Verify the knob is fully seated by checking that it sits flush with the control panel and doesn't wobble or move loosely.
16. Test the knob operation by turning it through all settings (OFF to HIGH or through all temperature settings). The knob should turn smoothly with positive detents or clicks at each setting.
17. Verify the knob stays in position when released at any setting. It should not slip or turn on its own.
18. Check the alignment of the temperature markings on the knob with the indicator on the control panel (if present). Markings should align properly at the OFF position.
19. If the knob is loose or doesn't stay in position, remove it and inspect the valve stem and knob shaft opening for damage or wear. The stem may be worn and require valve replacement.
20. If the knob operates properly and stays securely in position, the installation is complete.

Safety Notes: Allow the range to cool completely before handling knobs. Pull knobs straight out—do not twist or rock excessively. Align the D-shaped or keyed opening with the valve stem properly before pushing on. The knob should fit snugly and operate smoothly. This repair requires no tools and takes less than 1 minute per knob.

1. Always verify your range model number before ordering—control knobs are model-specific for proper fit and appearance. Knobs vary by shaft type (D-shaped vs. round), diameter, finish (stainless, black, white), and marking style. Using the wrong knob results in poor fit or mismatched appearance.
2. The D-shaped or keyed shaft opening must align with the valve stem flat side for proper installation. If the knob doesn't slide on easily, rotate it 180 degrees and try again. Forcing the knob onto a misaligned stem damages both the knob and valve stem.
3. If the new knob is loose or slips on the valve stem, the valve stem may be worn and require replacement. Over time, the D-shaped stem can wear round, preventing proper knob engagement. Replacing the knob won't fix a worn valve stem—the entire valve assembly needs replacement.
4. Control knobs typically last 10-15 years with normal use. Factors that shorten knob life include excessive heat exposure (knobs positioned too close to burners), frequent cleaning in dishwasher (causes warping and fading), impact damage from dropping or hitting, and exposure to harsh cleaning chemicals.
5. Never clean control knobs in the dishwasher—high heat and harsh detergents cause warping, fading, and damage. Hand wash knobs with mild soap and warm water, then dry thoroughly before reinstalling. This preserves markings and prevents warping.
6. When replacing one knob, consider replacing all knobs for uniform appearance and matching finish. Knobs fade and discolor over time, making a single new knob stand out. Replacing all knobs ensures consistent appearance and finish.
7. Stainless steel finish knobs require special care to prevent fingerprints and smudges. Clean with stainless steel cleaner or microfiber cloth to maintain appearance. Avoid abrasive cleaners that scratch the finish.
8. If knobs melt or warp repeatedly, check burner alignment and flame pattern. Improperly adjusted burners direct excessive heat toward knobs, causing melting. Gas burners should have blue flames with no yellow tips—yellow flames indicate improper air mixture and excessive heat.
9. Store spare knobs in a safe location away from heat sources. Knobs can warp or melt if stored near the range or in hot environments. Keep in a cool, dry location in original packaging.
10. Control knobs are cosmetic parts that don't affect range function—but worn or damaged knobs make temperature control difficult. Faded markings prevent accurate temperature selection. Loose knobs slip during cooking, changing settings unintentionally. Replace damaged knobs promptly for safe, accurate cooking control.