Whirlpool Washer Washer Motor Control Board WP8183196

Is This the Right Part?

Confirm the complete model number before ordering. Similar parts may use different connectors, dimensions, hose positions, electrical ratings, or mounting points.

Part Details

Installation Notes

1. Disconnect power and shut off water or gas where applicable.
2. Photograph wiring, hoses, clamps, and mounting positions.
3. Compare the new part with the original before installation.
4. Inspect nearby wires, hoses, seals, and connectors for damage.
5. Test the appliance and check for leaks, unusual sounds, or error codes.

Use a qualified technician when diagnosis or installation is outside your experience. Gas parts should be installed by a licensed technician.

No model hub pages are currently available for WP8183196-compatible washers. Contact us with your full model number and we'll confirm compatibility before you order.

The motor control board is mounted in the lower rear of the washer cabinet and communicates with the main control board to regulate motor operation. On Whirlpool Duet and Maytag Epic series front-loaders, this board is responsible for all drum rotation functions including wash agitation, spin cycles, and drain sequences. Failure is often triggered by power surges, moisture intrusion, or component fatigue over time.

Replacing WP8183196 resolves: washer not spinning or agitating, drum stopping mid-cycle, F/E error codes related to motor function, washer failing to start despite power being present, and unusual motor noise or vibration during operation.

OEM Whirlpool part number WP8183196. Genuine factory replacement — same board installed at time of manufacture. Compatible with Whirlpool Duet and Maytag Epic front-load washer platforms. Ships from XPart Supply's Canadian warehouse.

OEM/New — The original Whirlpool factory part. Full manufacturer specifications, exact fit, no modifications required. Out-of-stock orders accepted — ships when stock is replenished.

Used — A tested, functional pull from a decommissioned unit. Ideal for cost-conscious repairs where OEM pricing is a barrier. Out-of-stock purchases are not available on used inventory. Replacement parts are not affiliated with, sponsored by, or endorsed by Whirlpool Corporation or any OEM manufacturer.

WP8183196 (OEM current part number)

Disconnect power before beginning any repair. The motor control board is accessed by removing the lower front panel or rear access panel depending on your model. Discharge any capacitors before handling the board. Note the orientation and routing of all wire harnesses before disconnecting. Reconnect all connectors fully and restore power to test spin and agitation functions before reassembling the cabinet.

WFW9200SQ00, WFW9200SQ01, WFW9200SQ02, WFW9400SU00, WFW9400SU01, WFW9400SU02, WFW9400SW00, WFW9400SW01, WFW9400SW02, WFW9400VE00, WFW9400VE01, WFW9400VE02, WFW9500TW00, WFW9500TW01, WFW9500TW02, MFW9700SQ0, MFW9700SQ1, and 100+ additional models. Contact us with your model number to confirm compatibility.

How do I know if my motor control board has failed?
Common indicators include the washer not spinning or agitating, stopping mid-cycle, displaying F-series error codes related to motor function, or failing to start. A failed motor control board often produces no drum movement even when the washer powers on normally. Contact us if you need help diagnosing before ordering.

Is the used option reliable?
Our used boards are pulled from decommissioned units and tested for basic function. They are a cost-effective option for older machines where the repair cost needs to stay low. Used inventory is sold as-is with no backorder availability.

Does WP8183196 fit both Whirlpool and Maytag washers?
Yes — WP8183196 is cross-compatible across Whirlpool Duet and Maytag Epic front-load platforms that share the same motor control architecture. Confirm your full model number before ordering. Contact us to verify fit.