Oven Not Heating or Baking Unevenly – Fix a Failed Bake Element Fast with WS01F02249

When your GE range stops baking evenly or won't heat at all, a burned-out bake element is the most common cause. In most GE, GE Profile, and GE Café ranges, the lower bake element cycles on and off to maintain oven temperature — when it fails, the oven either won't heat or produces hot and cold spots that ruin every dish. ⚡ Don't keep cooking around a dead element — it only gets worse and can damage the oven liner. Part WS01F02249 is the genuine OEM replacement that restores full, even baking heat with no modification required.

❓ Is This the Right Part?

This is the correct fix if ALL of the following are true:

• ✔ Your appliance is a GE, GE Profile, or GE Café freestanding or slide-in range or wall oven
• ✔ The oven won't heat, heats slowly, or bakes unevenly (bottom heat issue)
• ✔ You can see visible burn marks, breaks, or blistering on the existing bake element
• ✔ Your model number is in the confirmed compatibility list (check tags or contact us)
• ✔ ONLY problem is a failed lower bake element — not a broil element, igniter, control board, or temperature sensor issue

🔧 Common Symptoms

• Oven won't heat up at all on bake mode
• Oven takes much longer than normal to reach temperature
• Food burns on top but stays raw on the bottom
• Visible burn hole, crack, or blister on the element coil
• Element glows red only partially or not at all
• Oven trips the breaker or blows a fuse when bake is selected

✔ If these symptoms match, this is the most likely failed component in the system.

✔ In most cases, replacing this bake element restores normal oven operation immediately.

📦 Part Details

• Part Number: WS01F02249
• Type: Range / Oven Bake Element (Lower)
• Replaces: WB44M180, 222D4887G001 (no modification required)
• Brands: GE, GE Profile, GE Café, Monogram

⚙️ Installation Notes

Skill Level: Easy (2/5) — 15–25 minutes. Disconnect power to the range at the breaker or by unplugging before beginning — the bake element carries 240V and must be fully de-energized. Open the oven door, remove the oven racks, and unscrew the two mounting screws at the back of the element. Gently pull the element forward to expose the wire connectors, disconnect them, and reverse the process with the new element. Do not force the connectors — if they are corroded or fused, replace the connector terminals as well to avoid arcing.

💡 Pro Tip

🔗 Model Hub Pages

CC2S986SEL1SS, CCHS985SEL1SS, JCB530DJ1BB, JCB530DJ1WW, JCB530SF2SS, JCB530SJ1SS, JCB530SJ2SS, JCB560DJ1WW, JCB560DJ2WW, JCB830DJ1WW, JCB830DK1WW, JCB830SF3SS, JCB830SJ1SS, JCB830SK1SS, JCB840DF2WW, JCB840DJ1WW, JCB840DK1WW, JCB840EJ1ES, JCB840EK1ES, JCB840SF2SS, JCB840SJ1SS, JCB840SK1SS, JCB860DF2WW, JCB860DJ1WW, JCB860DK1WW, JCB860SJ1SS, JCB860SJ1SV, JCB860SK1SS, JCB870SF2SS, JCB870SJ1SS, JCB870SK1SS, JCBP720ST3WW, JCBP720ST4WW, JCBS660DF2WW, JCBS660DJ1WW, JCBS660DK1WW, JCBS660SF3SS, JCBS660SJ1SS, JCBS660SK1SS, JCS630DF2BB, JCS630SF2SS, JCS630SF3SS, JCS860DF2BB, JCS860DF2WW, JCS860DF3BB, JCS860DF3WW, JCS860EF1ES, JCS860EF2ES, JCS860EF3ES, JCS860SF2SS, JCS860SF3SS, JCSP41SV4SS, JCSP41SV5SS, JCSP42DR3WW, JCSP46DR3WW, MBR12DGH1WW, P2S968DER3BB, PC2S910SEF2SS, PC2S910SEF3SS, PC2S910SEF4SS, PC2S920EEJ1ES, PC2S920EEJ3ES, PC2S920SEF2SS, PC2S920SEF3SS, PC2S920SEF4SS, PC2S920SEF5SS, PC2S930SEL1SS, PCB905SJ1SS, PCB905SK1SS, PCB909SR3SS, PCB915EK1ES, PCB915SK1SS, PCB940EK1ES, PCB940SK1SS, PCB969DR2WW, PCB980DF2WW, PCB980DF3BB, PCB980DF3WW, PCB980SF2SS, PCB980SF3SS, PCB985DK1WW, PCB985EK1ES, PCB985SK1SS, PCS940DF2BB, PCS940DF2WW, PCS940DF3WW, PCS940DF4BB, PCS940DF4WW, PCS940EJ1ES, PCS940EJ2ES, PCS940SF2SS, PCS940SF3SS, PCS940SF4SS, PCS968DR3WW, PDT760SSFSS