Menu
Oven Won’t Ignite or Reach Temperature? Igniter WS01F10532 – Fix a Dead or Weak GE Gas Oven Fast
A gas oven that won’t light, takes forever to preheat, or shuts off mid-cycle almost always has a failed igniter — and it’s the most common repair on GE gas ranges. In most GE gas ovens, this is caused by a failed glowbar igniter. When it fails, the igniter either won’t glow at all or glows weakly and can’t draw enough current to open the gas valve — so the burner never lights and the oven never heats. ⚡ Common failure point in GE gas ovens and ranges. Part WS01F10532 is the genuine OEM replacement that restores full ignition and heating performance with no modifications required.
❓ Is This the Right Part?
This is the correct fix if ALL of the following are true:
- ✔ Gas supply to the range is confirmed on and flowing
- ✔ Stovetop burners ignite and operate normally
- ✔ Oven control board and temperature sensor have been checked
- ✔ ONLY problem is oven won’t light, won’t heat, or takes excessively long to preheat
Not sure? Send us your model number — we’ll confirm before you order.
🔧 Common Symptoms
- Oven won’t ignite — no flame, no heat
- Igniter glows orange but burner never lights (weak igniter)
- Oven takes 20+ minutes to preheat or never reaches set temperature
- Oven shuts off mid-cycle and won’t restart
- Smell of gas without ignition (igniter not drawing enough current to open valve)
✔ If these symptoms match, this is the most likely failed component in the system.
✔ In most cases, replacing this igniter restores normal oven operation immediately.
📦 Part Details
- Part Number: WS01F10532
- Type: Gas Oven Igniter / Glowbar Igniter
- Brands: GE
⚠️ Recommended While Repairing:
While the oven is open, inspect the bake element wiring harness and oven temperature sensor for heat damage or corrosion. A failing temperature sensor can cause the same “won’t heat” symptom and is inexpensive to replace at the same time — saving a second service call.
While the oven is open, inspect the bake element wiring harness and oven temperature sensor for heat damage or corrosion. A failing temperature sensor can cause the same “won’t heat” symptom and is inexpensive to replace at the same time — saving a second service call.
⚙️ Installation
Skill Level: Easy — 20–30 minutes. Disconnect power and shut off gas before servicing. Remove the oven racks and bottom panel to access the igniter mounted on the burner assembly. Disconnect the two-wire harness, remove the mounting screws, and install the new igniter in reverse order. Do not touch the igniter element with bare hands — skin oils reduce lifespan. Restore power and gas, then run a test cycle to confirm ignition.
✓ Compatible Models
Fits GE gas oven and range models. Contact us to verify your model number before ordering.
💡 Pro Tip
Weak Glow = Failed Igniter, Even If It Lights Sometimes:
A glowbar igniter that glows orange but takes more than 90 seconds to light the burner is already failing — it’s drawing insufficient current to fully open the gas valve. Don’t wait for a complete failure. A weak igniter causes incomplete combustion, uneven heating, and repeated mid-cycle shutoffs. Replace it now and avoid a cold oven on the worst possible night.
A glowbar igniter that glows orange but takes more than 90 seconds to light the burner is already failing — it’s drawing insufficient current to fully open the gas valve. Don’t wait for a complete failure. A weak igniter causes incomplete combustion, uneven heating, and repeated mid-cycle shutoffs. Replace it now and avoid a cold oven on the worst possible night.
✅Compatibility & Cross Reference
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
Buy Online Pick Up In-Store
Address
101 Trillium Dr
Kitchener, Ontario N2E 1W8
Kitchener, Ontario N2E 1W8
Phone
Hours
Mon–Fri 9 AM–5 PM • Sat 9 AM–1 PM
- Choosing a selection results in a full page refresh.
