Menu
⚠️ DISCONTINUED PART — New OEM stock is no longer available. New (OEM) and Used options available while supplies last. Order now — no restock expected.
GE Range Oven Not Heating or Showing Temperature Errors? Oven Control Board WS01F04306 – Fix Control Board Failure Fast
A GE range oven that won't heat, displays error codes, or behaves erratically is almost always a failed oven control board. In most GE dual-fuel and electric ranges, the oven control board is the central brain that manages bake and broil element activation, temperature regulation, and cycle timing. When it fails — through relay burnout, capacitor failure, or firmware corruption — the oven may refuse to heat, display fault codes, run at the wrong temperature, or go completely unresponsive. ⚡ Common failure point in GE CC2S985 series ranges. Part WS01F04306 is the genuine OEM oven control board that restores accurate temperature control and full oven function — directly superseding WB27K10382, WB27K10422, WS01F01042, and 164D6476G087.
❓ Is This the Right Part?
This is the correct fix if ALL of the following are true:
- ✔ Range powers on — display and surface burners work normally
- ✔ Bake and broil elements test good (continuity confirmed with multimeter)
- ✔ Oven temperature sensor (RTD probe) tests within spec (~1,080–1,090 ohms at room temp)
- ✔ ONLY problem is oven not heating, displaying error codes, or behaving erratically
Not sure? Send us your model number — we'll confirm before you order.
🔧 Common Symptoms
- Oven does not heat on bake or broil despite elements testing good
- Oven displays error or fault codes (F-codes) on the control panel
- Oven heats to the wrong temperature — overcooks or undercooks consistently
- Oven starts a cycle then shuts off prematurely with no error
- Control panel unresponsive or buttons not registering correctly
- Oven worked fine then went dead after a power surge or self-clean cycle
✔ If these symptoms match, the oven control board is the most likely failed component.
✔ In most cases, replacing this control board restores full, accurate oven operation immediately.
📦 Part Details
- Part Number: WS01F04306
- Type: Oven Control Board (Electronic Range Control / ERC)
- Replaces / Supersedes: WB27K10382, WB27K10422, WS01F01042, 164D6476G087
- Brands: GE
- Status: ⚠️ Discontinued / No Longer Available (NLA) — new and used stock only while supplies last
⚠️ Used Condition Notice: Used control boards are genuine GE pulls from working units, tested before shipping. They carry the same fit guarantee as new OEM — correct part, correct fit. Stock is limited and sold as-is with no implied warranty beyond fit confirmation.
⚠️ Recommended While Repairing:
Before installing the new control board, test the oven temperature sensor (RTD probe) resistance. A drifted or failed sensor causes the control board to overheat the oven, which can burn out the new board’s relays within weeks. If the sensor reads outside 1,080–1,090 ohms at room temperature, replace it at the same time. One service call, two parts, zero repeat failures.
Before installing the new control board, test the oven temperature sensor (RTD probe) resistance. A drifted or failed sensor causes the control board to overheat the oven, which can burn out the new board’s relays within weeks. If the sensor reads outside 1,080–1,090 ohms at room temperature, replace it at the same time. One service call, two parts, zero repeat failures.
⚙️ Installation
Skill Level: MODERATE — 20–40 minutes. Disconnect power at the breaker before servicing. The control board is located behind the rear control panel — remove the panel screws (typically 4–6 at the rear of the range), photograph all wiring harness connector positions before unplugging, then swap in the new WS01F04306 board and reconnect all harnesses in the same positions. Reassemble the panel, restore power, and run a bake cycle to confirm accurate temperature control.
✓ Compatible Models
Confirmed compatible with CC2S985SET2SS, CC2S985SET3SS, CC2S985SET4SS, CC2S985SET5SS, CC2S985SET6SS, CC2S985SET7SS, CC2S985SET8SS. Contact us to verify your model number before ordering.
💡 Pro Tip
Test the Sensor Before Blaming the Board:
Control board failures on GE ranges are often misdiagnosed — the oven temperature sensor (RTD probe) is the more common failure and costs a fraction of the price. Before ordering a control board, test the sensor resistance with a multimeter at room temperature. A good sensor reads approximately 1,080–1,090 ohms. If it reads open, shorted, or wildly out of range, replace the sensor first. If the sensor tests good and the oven still won’t heat or throws F-codes, the control board is confirmed as the fault.
Control board failures on GE ranges are often misdiagnosed — the oven temperature sensor (RTD probe) is the more common failure and costs a fraction of the price. Before ordering a control board, test the sensor resistance with a multimeter at room temperature. A good sensor reads approximately 1,080–1,090 ohms. If it reads open, shorted, or wildly out of range, replace the sensor first. If the sensor tests good and the oven still won’t heat or throws F-codes, the control board is confirmed as the fault.
✅Compatibility & Cross Reference
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
Buy Online Pick Up In-Store
Address
101 Trillium Dr
Kitchener, Ontario N2E 1W8
Kitchener, Ontario N2E 1W8
Phone
Hours
Mon–Fri 9 AM–5 PM • Sat 9 AM–1 PM
- Choosing a selection results in a full page refresh.
